background image

8

Illustration

7.

 Installation 

Check

4. Drill holes for the remaining four screws.

5. Hang the unit again by the first screw, and then 

insert and tighten the remaining four screws.

6. Take waterproofing measures so that water does 

not enter the building from screws mounting the 

device.

•  Make sure the unit is installed securely so that it will 

not fall or move due to vibrations or earthquakes.

Securing to the wall

1. Drill a single screw hole, making sure to hit a stud.
2. Insert and tighten the screw and hang the  unit by  

the upper wall mounting bracket.

3. Determine the positions for the remaining four screws 

(two for the top bracket and two for the bottom), and 

remove the unit. 

•  The weight of the device will be applied to the wall. If the strength of the wall is not 

sufficient, reinforcement must be done to prevent the transfer of vibration.

•  Do not drop or apply unnecessary force to the device when installing. Internal parts may 

be damaged and may become highly dangerous.

•  Install the unit on a vertical wall and ensure that it is level.

Locating Screw Holes

Mounting

Structure

•  When installing with bare hands, take caution to 

not inflict injury.

•  Be careful not to hit electrical wiring, gas, or water 

piping while drilling holes.

Item

CAUTION

Be sure to do

Mounting Bracket

(upper)

Anchoring Screw

Location of Screw Hole

Locating Screw Holes

Installations at Elevations 

Above 2,000 ft.

•  Adjust  the  dip  switches  as  illustrated  in  the  table  to 

the right if this water heater is installed at an altitude 

of 2000 ft. (610m) or higher. 

•  Disconnect  power  to  the  water  heater  before 

changing  the  dip  switches.    Failure  to  perform  this 

step will result in a "73" code displayed on the remote 

controller  and  a  cease  in  operation.    If  this  occurs, 

disconnect, then reconnect power to the water heater 

to reset the system.

  Note : Please refer to page 23 for the location of the 

dip switch bank.

* Do not change any other dipswitches.

* High elevation adjustment.

6

5

2,001 - 4,000 ft (611 - 1,220m)

0 - 2,000 ft (0 - 610m)

ON=

OFF=

4,001 - 6,000 ft (1,221 - 1,830m)
6,001 - 8,000 ft (1,831 - 2,440m)

Summary of Contents for NC199-OD






































Reviews: