background image

5

5.

 Choosing Installation Site

*  Locate the appliance in an area where leakage from the unit or connections will not result in damage 

to the area adjacent to the appliance or to the lower floors of the structure. 

When such installation 

locations cannot be avoided, a suitable drain pan, adequately drained, must be installed under the 

appliance. The pan must not restrict combustion air flow.

As with any water heating appliance, the potential for leakage at some time in the life of the product 

does exist. The manufacturer will not be responsible for any water damage that may occur.

•  Locate the vent terminal so that there are no obstacles around  the termination and so that exhaust 

can't accumulate. Do not enclose the termination with corrugated metal or other materials.

•  Avoid places where fires are common, such as those where gasoline, 

benzene and adhesives are handled, or places in which corrosive gases 

(ammonia, chlorine, sulfur, ethylene compounds, acids) are present.

     Using the incorrect voltage may result in fire or cracking.
•  Avoid installation in places where dust or debris will accumulate.

Dust may accumulate and reduce the performance of the unit's fan. 

This can result in incomplete combustion.

•  Avoid installation in places where special chemical agents 

  (e.g., hair spray or spray detergent) are used.

Ignition failures and malfunction may occur as a result.

•  Carbon Monoxide Poisoning Hazard. Do not install this water heater in a 

recreational vehicle or on a boat.

• The manufacturer does not recommend installing the water heater in an 

attic due to safety issues. 

  If you install the water heater in an attic:

• 

Make sure the unit will have enough combustion air and proper ventilation.

• 

Keep the area around the water heater clean. Dust may accumulate and 

reduce the performance of the unit's fan. This can result in incomplete 

combustion.

•  Place the unit for easy access for service and maintenance.

•  A drain pan, or other means of protection against water damage, is 

required to be installed under the water heater in case of leaks.

Prohibited

DANGER

WARNING

Summary of Contents for GQ-2457WS-FFA US

































Reviews: