background image

R6GP - 072/090/120 Series

Installation Instructions

Single Package Gas Heating/Electric Cooling Rooftop Units

R6GP-090 Shown

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. This includes being able to install the product according to strict safety 
guidelines and instructing the customer on how to operate and maintain the equipment for the life of the product. Safety should always be the 
deciding factor when installing this product and using common sense plays an important role as well. Pay attention to all safety warnings and 
any other special notes highlighted in the manual. Improper installation of the unit or failure to follow safety warnings could result in serious 
injury, death, or property damage. These instructions are primarily intended to assist qualifi ed individuals experienced in the proper installation 
of this appliance. Some local codes require licensed installation/service personnel for this type of equipment. After completing the installation, 
return these instructions to the customer’s package for future reference.

WARNING:

!

DO NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

FIRE OR EXPLOSION HAZARD

• Failure to follow safety warnings exactly 

could result in serious injury or property 
damage.

• Installation and service must be performed 

by a qualifi ed installer, service agency or the 
gas supplier.

• Do not store or use gasoline or other 

fl ammable vapors and liquids in the vicinity 
of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not 

use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a 

neighbors phone. Follow the gas suppliers 

instructions.

• If you cannot reach your gas supplier, call 

the fi re department.

High Effi ciency

Summary of Contents for R6GP-072 Series

















































Reviews: