background image

42

CAPACITY OF BLACK IRON GAS PIPE (CU. FT. PER HOUR) 

FOR NATURAL GAS (SPECIFIC GRAVITY - 0.60)

NOMINAL BLACK IRON PIPE 

DIAMETER (IN.)

LENGTH OF PIPE RUN (FT)

10

20

30

40

50

60

70

80

1/2

130

90

75

65

55

50

45

40

3/4

280

190

150

130

115

105

95

90

1

520

350

285

245

215

195

180

170

1 1/4

1050

730

590

500

440

400

370

350

1 1/2

1600

1100

890

760

670

610

NOTES

The cubic feet per hour listed in the table above must be greater than the cubic feet per hour of gas fl ow required by the furnace. To determine the 
cubic feet per hour of gas fl ow required by the furnace, divide the input rate of the furnace by the heating value (from gas supplier) of the gas:

Cubic Feet Per Hour Required =

Input To Furnace (Btu/hr)

Heating Value of Gas (Btu/Cu. Ft.)

Table 14. Black Iron Gas Pipe Capacities

Table 15. Orifi ce or Drill Size for Natural and Propane (LP) Gases

ALTITUDE ABOVE SEA LEVEL

0 to

2,000 FT

2,001 to

4,000 FT

4,001 to

6,000 FT

6,001 to

8,000 FT

8,001 to

10,000 FT

 UNIT MODEL

NUMBER

GAS

TYPE

HEATING

INPUT

(BTU/HR)

NUMBER

OF

BURNERS

ORIFICE SIZE

R6GP-072*-100C

Natural

100,000

3

36

38

40

41

43

Propane

85,000

53

54

54

55

55

R6GP-072*-166C

Natural

166,000

5

36

38

40

41

43

Propane

141,000

53

54

54

55

55

R6GP-090*-200C

Natural

200,000

6

36

38

40

41

43

Propane

175,000

51

52

52

52

53

R6GP-120*-235C

Natural

235,000

7

36

38

40

41

43

Propane

205,000

51

52

52

52

53

* Refer to Instructions for High Altitude Deration (pages 11 - 12) to determine heat exchanger capacity at increased elevations.

GAS INFORMATION

Table 16. Heating Rise/Range

MODEL

GAS

TYPE

HEATING 

INPUT

HEATING 

OUTPUT

HEATING RISE 

RANGE (°F)

CFM RANGE

1,950

2,100

2,250

2,400

2,550

2,700

SCFM

R6GP-072*-100C

Natural

100,000

80,000

15 - 45

38

35

33

31

29

27

RISE (°F)*

Propane

85,000

68,000

32

30

28

26

25

23

1,950

2,100

2,250

2,400

2,550

2,700

SCFM

R6GP-072*-166C

Natural

166,000

133,000

35 - 65

63

59

55

51

48

46

RISE (°F)*

Propane

141,000

112,800

54

50

46

44

41

39

2,425

2,625

2,800

3,000

3,188

3,375

SCFM

R6GP-090*-200C

Natural

200,000

157,000

30 - 60

60

55

52

48

46

43

RISE (°F)*

Propane

175,000

137,000

52

48

45

42

40

38

3,250

3,500

3,750

4,000

4,250

4,500

SCFM

R6GP-120*-235C

Natural

235,000

185,000

25 - 55

54

50

46

44

41

39

RISE (°F)*

Propane

205,000

164,000

47

43

40

38

36

34

* At elevations of 2,000 feet or less.

Summary of Contents for R6GP-072 Series

















































Reviews: