Nordson Encore Installation, Troubleshooting, Repair Download Page 96

Page: 96 / 97

CRITICAL

No revisions permitted without

approval of the proper agency.

ENCORE ENHANCE

INTERFACE

CONTROLLER UNIT

(1614566)

ENCORE ENGAGE

EXTERNAL

CONTROL CONSOLE

REVISIONS

ZONE

REV.

DESCRIPTION

CHK

ECO NO.

DATE

ISSUED

BDM

25JAN19

RELEASED TO PRODUCTION

BDM

PE-101281

22FEB19

ADDED SHEET 2

DRJ

PE-102174

22OCT19

THE FOLLOWING CONTROLLERS ARE FOR USE IN UNCLASSIFIED LOCATIONS AND

NON-EXPLOSIVE ATMOSPHERES:

1615950

CONTR,EXT,4 GUN,ENCORE ENGAGE

1615951

CONTR,EXT,6 GUN,ENCORE ENGAGE

1615952

CONTR,EXT,8 GUN,ENCORE ENGAGE

1615953

CONTR,EXT,10 GUN,ENCORE ENGAGE

1615954

CONTR,EXT,12 GUN,ENCORE ENGAGE

1615955

CONTR,EXT,14 GUN,ENCORE ENGAGE

1615956

CONTR,EXT,16 GUN,ENCORE ENGAGE

THE APPLICATORS AND CABLES ARE SUITABLE FOR CLASS ll, DIV 1, GROUP F & G

HAZARDOUS (CLASSIFIED) LOCATIONS, OR <Ex> II 2 D EXPLOSIVE ATMOSPHERES:

GUNS:

1097489

APPLICATOR,BAR MT,AUTO,ENCORE

1099824

APPLICATOR,TUBE MT,AUTO,ENCORE,5FT

1097500

APPLICATOR,TUBE MT,AUTO,ENCORE,6FT

1606986

APPLICATOR,TUBE MT,AUTO,ENCORE,5FT PVC

1606969

APPLICATOR,BAR MT,ENCORE HD AUTO

1606970

APPLICATOR,TUBE MT,AUTO,5FT ENCORE HD

1606985

APPLICATOR,TUBE MT,AUTO,5FT PVC ENCORE HD

1606971

APPLICATOR,TUBE MT,AUTO,6FT ENCORE HD

OPTIONS:

1604084

EXTENSION,SPRAY,90 DEGREE,ENCORE

1605614

EXTENSION,SPRAY,60 DEGREE,ENCORE

1605703

EXTENSION,SPRAY,45 DEGREE,ENCORE

1609048

POS MULTIPLIER

CABLES:

1097537

CABLE,AUTO,ENCORE,8M

1097539

CABLE,AUTO,ENCORE,12M

1097540

CABLE,AUTO,ENCORE,16M

1601344

CABLE,EXTENSION,ENCORE AUTO,4M

THE APPLICATORS AND CABLES ARE SUITABLE FOR CLASS ll, DIV 1, GROUP F & G

HAZARDOUS (CLASSIFIED) LOCATIONS, OR <Ex> II 2 D EXPLOSIVE ATMOSPHERES:

GUNS:

1603160

APPLICATOR ASSY,MANUAL,ENCORE HD

CABLES:

1600745

CABLE ASSY,ENCORE XT/HD,6M

1085168

CABLE EXTENSION,6-CONDUCTOR,SHIELDED,6M

OPTIONS:

1609048

POS MULTIPLIER

THE FOLLOWING CONTROLLER IS FOR USE IN CLASS II, DIV 2 HAZARDOUS

(CLASSIFIED) LOCATIONS OR <Ex> II (2)3D EXPLOSIVE ATMOSPHERES:

1615957

KIT,ENGAGE,MANUAL GUN,DUAL,ENCORE HD

1615960

KIT,ENGAGE,MANUAL GUN,QUAD,ENCORE HD

1614566

CONTR UNIT,INTERFACE,ENCORE ENHANCE

THIS DRAWING IS NORDSON PROPERTY,CONTAINS PROPRIETARY INFORMATION AND MUST BE RETURNED UPON REQUEST.
DO NOT CIRCULATE, REPRODUCE OR DIVULGE TO OTHER PARTIES WITHOUT WRITTEN CONSENT OF NORDSON.

NOTICE

FILE NAME

MATERIAL NO.

REVISION

SCALE

ALL DIMENSIONS IN

REF DWG,APPROVED EQUIPMENT,ENGAGE

CADD GENERATED DWG.

NORDSON CORPORATION

WESTLAKE, OH, U.S.A. 44145

DRAWN BY

CHECKED BY

EXCEPT AS NOTED

THIRD ANGLE
PROJECTION

X±0.8

X.X±0.25

MACHINED SURFACES

1.6

BREAK INSIDE/OUTSIDE CORNERS

0.1/0.8

THREAD LENGTH DIMENSIONS ARE

FULL THREAD

INTERPRET DRAWINGS PER ASME

Y14.5-2009

PERFECT FORM AT MMC REQUIRED

FOR INTERRELATED FEATURES

DESCRIPTION

DATE

APPROVED BY

RELEASE NO.

SIZE

MATERIAL NO.

REVISION

BDM

25JAN19

PE-101281

10018643

1:6

SHEET

X.XX±0.13

10018643

Summary of Contents for Encore
































































































Search results

Summary of Contents for Encore

Reviews:

Related manuals for Encore

Brands by name

Popular brands

Nordson Encore, Installation, Troubleshooting, Repair

Search results

Summary of Contents for Encore

Reviews:

Related manuals for Encore

Brands by name

Popular brands