Nordson Encore HD iControl System Page 41 Hardware Manual Download

Page: 41 / 93

Troubleshooting

4-1

Part 1603054-02

2015 Nordson Corporation

Section 4

Troubleshooting

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

CAUTION:

Do not turn off console power without first performing a program

shutdown. Doing so could corrupt the iControl program and operating

system on the program card. Refer to

Program Shutdown

in the

Configuration

section of the

iControl Operator Interface

manual for the

shutdown procedure.

NOTE:

If the troubleshooting procedures in this section do not solve your

problem, contact the Nordson Industrial Coating Systems Customer Support

Center at (800) 433

−

9319 or your local Nordson representative.

Error Codes and Alarm Messages

Table 4-1 Error Codes and Messages

Code

Message Text

Description

Refer to

Page

NA = Not currently applicable
*

−

Code may differ on early software releases

10x

CAN and Node State

101

CAN bus fault detected

N/A

4-6

102

CAN receive buffer overflow

Host CAN interface receive too much data

and could not process it quickly enough

4-6

103

Message timeout

Remote CAN device did not respond to a

direct message in the allotted time.

4-6

104

Went offline

Remote CAN device is no longer online

4-6

105

Returned to online

Remote CAN device returned to service

4-6

106

Communication error

Host CAN interface detected a communication

error

107

BUS

−

OFF

255 bad CAN messages received

108

Warning Limit exceeded

127 bad CAN messages received

109

Bit error

Dominant bit not detected in 5 data bits

110

Form error

Fixed format data field contains illegal bits

111

Stuffing error

Recessive bit not detected in 5 data bits

Continued...

Obsolete

Summary of Contents for Encore HD iControl System






























































































Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands

Nordson Encore HD iControl System, Hardware Manual

Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands