manualshive.com logo in svg

Nordson 1006453A, Customer Product Manual, Page: 21 / 24

Share
Download
Nordson 1006453A Customer Product Manual Download Page 21

Ejector Gun Controller

17

E

2001 Nordson Corporation

All rights reserved

1006453A

Issued 6/01

Manual 25-23

Follow these procedures to replace the keypad on the front of the Ejector
gun controller enclosure.

See Figure 4.

1. Disconnect power at the knife disconnect and open the controller

door.

2. Unplug the communication cable (6) from the keypad (1).

3. Remove the nuts that secure the keypad to the enclosure door.

Remove the keypad from the door.

4. Install a new keypad and tighten the nuts.

5. Download the most current Ejector gun program according to your

programming software literature, using the cables supplied for
downloading.

6. Reconnect the power cable.

7. Close the controller door and restore the power connection at the

knife disconnect.

Follow these procedures to replace the power supply.

See Figure 4.

1. Disconnect power at the knife disconnect and open the controller

door.

2. Disconnect the wires going to the power supply (3).

3. Remove the power supply from the DIN rail.

4. Install the new power supply onto the DIN rail.

5. Connect the wires per the electrical schematics provided with your

system documentation.

6. Close the controller door and restore the power connection at the

knife disconnect.

Replacing the Keypad

Replacing the Power Supply

Summary of Contents for 1006453A

























Reviews:

No comments