manualshive.com logo in svg

Nordson 1006453A, Customer Product Manual, Page: 17 / 24

Share
Download
Nordson 1006453A Customer Product Manual Download Page 17

Ejector Gun Controller

13

E

2001 Nordson Corporation

All rights reserved

1006453A

Issued 6/01

Manual 25-23

WARNING:

 

 

Allow only qualified personnel to perform the

following tasks.  Follow the safety instructions in this document
and all other related documentation.

Follow these guidelines to keep the Ejector gun controller maintained:

S

Follow all plant safety lockout procedures.

S

Keep the controller door closed except when performing maintenance
and repair inside the enclosure.

CAUTION:  

Do not use solvents to clean any part of the

controller.  Using solvents to clean the controller can damage its
components.

S

Periodically clean the keypad with a soft, damp cloth.

S

Periodically check the tightness of all wire termination screws.

WARNING:

 

 

Allow only qualified personnel to perform the

following tasks.  Follow the safety instructions in this document
and all other related documentation.

This section contains troubleshooting procedures.  These procedures
cover only the most common problems that you may encounter.  If you
cannot solve the problem with the information given here, contact your
local Nordson representative for help.

5. Maintenance

6. Troubleshooting

Summary of Contents for 1006453A

























Reviews:

No comments