NordicTrack ASR 630 User Manual Download

Page: 20 / 28

Inspect and tighten all parts of the elliptical exerciser

regularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and

a small amount of mild soap.

IMPORTANT: To avoid

damage to the console, keep liquids away from

the console and keep the console out of direct

sunlight.

BATTERY REPLACEMENT

If the console displays become dim, the batteries

should be replaced; most console problems are the

result of low batteries. See assembly step 9 on page

9 for replacement instructions.

HANDGRIP PULSE SENSOR TROUBLESHOOTING

If the handgrip pulse sensor does not function proper-

ly, see step 5 on page 16.

HOW TO ELIMINATE RUBBING OF THE DISCS

If the Discs (12) rub against the Side Shields (14, 15)

during use, make sure that the Center Foot (40) is

installed in the Frame (1). If the Center Foot is

installed, loosen the two indicated Bolt Sets (88) and

the two M4 x 19mm Screws (81) in each side of the

elliptical exerciser.

Adjust the position of the Side Shields (14, 15) until

the Discs (12) no longer rub against them, and then

tighten the Bolt Sets (88) and the M4 x 19mm Screws

(81).

HOW TO ADJUST THE BELT

If the pedals slip while you are pedaling, even while

the resistance is adjusted to the highest setting, the

belt may need to be adjusted. To adjust the belt, first

see assembly step 12 on page 11 and remove the left

pedal arm and the left link arm.

Then, carefully

pry off the left

Disc Cover (13)

using a flat

screwdriver. Next,

remove the four

screws (not

shown) from the

center of the left

Disc (12). Gently

rotate the Disc

Cover and the

Disc away from the elliptical exerciser.

Loosen, but do

not remove, the

three indicated

screws (A). Insert

the shaft of a

screwdriver

downward

between the

Idler (47) and the

Idler Pulley (48).

Pull the top of the

screwdriver

toward the front

of the elliptical exerciser until the Belt (74) is tight.

Then, tighten the three screws.

Reattach the left disc with the four screws and then

reattach the left disc cover. Next, see assembly step

12 on page 11 and reattach the left pedal arm and the

left link arm.

MAINTENANCE AND TROUBLESHOOTING

14, 15

Summary of Contents for ASR 630





























Search results

Summary of Contents for ASR 630

Reviews:

Related manuals for ASR 630

Brands by name

Popular brands

NordicTrack ASR 630, User Manual

Search results

Summary of Contents for ASR 630

Reviews:

Related manuals for ASR 630

Brands by name

Popular brands