background image

•  during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to cycles of intense 

use or of absolute standstill when season changes;

•  the new appliance, before being considered seasoned has to be subject to many start cycles to allow all materials and paints to 

complete the various elastic stresses;

•  in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress, as well as of wet 

paint. This paint, although during the manufacture it is backed at 250 °C for some hours, must exceed many times and for a given 

period of time the temperature of 350 °C before becoming completely embedded in the metallic surfaces.

Therefore, it is extremely relevant to take these easy steps during the lighting:

1.  Make sure that a strong air change is assured in the room where the appliance is installed.

2.  During the first starts, do not load excessively the combustion chamber (about half the quantity indicated in the instructions manual) 

and keep the product continuously ON for at least 6-10 hours with the registers less open than the value indicated in the instructions 

manual.

3.  Repeat this operation for at least 4-5 or more times, according to your possibilities.

4.  Then load more and more fuel (following in any case the provisions contained in the installation booklet concerning maximum load) 

and, if possible, keep the lighting periods long avoiding, at least in this initial phase, short ON/OFF cycles.

5.  During the first starts, no object should be leaned on the appliance and in detail on enamelled surfaces. Enamelled surfaces must 

not be touched during heating.

6.  Once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt heating with 

excessive loads.

After testing the proper working of the appliance, some days from the installation, it is possible to proceed with the construction 

of its aesthetic covering

.

WARNING

: During the surround building operations it must kept in mind possible and subsequent electrical installed parts maintenance 

(Fans, temperature probe, etc) and with hydraulic systems all parts connected to the thermo-fireplace.

9.1.  LOW EMISSION fire lighting

Smokeless combustion is a way of lighting a fire able to significantly reduce the emission of harmful substances. The wood burns gradually 

from the top downwards, so combustion is slower and more controlled. Burnt gases pass through the high temperatures of the flame and 

therefore burn almost completely. A load will last from 6 to 8 hours. 

Place the logs in the hearth a certain distance apart as shown in the 

Picture 9 at page 43

. Arrange the largest at the bottom and the smallest 

at the top, or vertically in the case of tall narrow combustion chambers. Place the fire starter module on top of the pile, arranging the first 

logs in the module at right angles to the pile of wood. 

Fire STARTER MODULE

This fire starter module replaces a paper or cardboard starter. 

Prepare four logs, 20 cm long with a cross section of 3 cm by 3 cm 

Picture 9 at page 43

Cross the four logs and place them on top of the 

pile of wood at right angles, with the fire lighter (wax impregnated wood fibre for example) in the middle.  The fire can be lit with a match. 

If you want, you can use thinner pieces of wood. In this case, you will need a larger quantity. 

Keep the flue gas exhaust valve and combustion air regulator open  (

1A

 - 

2A

). After lighting the fire, leave the combustion air regulator 

open in the position shown in the 

Picture 9 at page 43

IMPORTANT:

• 

do not add further wood between one complete load and the next;

• 

do not suffocate the fire by closing the air intakes;

• 

regular cleaning by a chimney sweep reduces fine particle emissions. 

These instructions are backed by ENERGIA Legno SVIZZERA 

 

www.energia-legno.ch

 

10. NORMAL OPERATION

After having positioned the registers correctly, insert the indicated hourly wood load avoiding overloads that cause anomalous stresses 

and deformations. 

You should always use the product with the door closed in order to avoid damages due to overheating (forge 

effect)

The inobservance of this rule makes the warranty expire

.

With the registers located on the front of the device, it is possible to adjust the heat emission of the same. They have to be opened 

according to the calorific need. The best combustion (with minimum emissions) is reached when, by loading the wood, most part of the air 

for combustion flows through the secondary air register. 

Never overload the appliance. Too much fuel and too much air for the combustion may cause overheating and then damage the 

product.

You should always use  the appliance with the door closed  in order to avoid damages due to overheating (forge effect).

The adjustment of the registers necessary to reach the rated calorific yield with a depression at the stack of 14 Pa (1,4 mm of column 

of water) is the following one: see chap. TECHNICAL DESCRIPTION.  

The appliance works as an intermittent operating appliance

.

Besides the adjustment of the air for the combustion, the intensity of the combustion and consequently the thermal performance of the 

device is influenced by the stack. A good draught of the stack requires a stricter adjustment of air for combustion, while a poor draught 

requires a more precise adjustment of air for combustion.

To verify the good combustion, check whether the smoke coming out from the stack is transparent. 

If it is white, it means that the device is not properly adjusted or the wood is too wet; if instead the smoke is gray or black, it signals that the 

combustion is not complete (it is necessary a greater quantity of secondary air).

MONOBLOCCHI  600 - 750 - 900 

20

 

6098700 - IT-EN-DE-FR

Summary of Contents for Monoblocco Piano 600

































Reviews: