11
NORDIC
The saw chain must not sag, although it should be possible to pull it 1-2 millimetres away from the guide
bar in the centre of the guide bar.
BEFORE STARTING THE EQUIPMENT
Caution! Do not fit the battery until the equipment has been fully assembled and all the settings have
been actuated. Always wear protective gloves when working on the equipment to protect yourself
against injury. Carefully unpack all parts and check that they are complete.
NOTE: The tension of a new chain must be checked after a few minutes in operation, and adjusted if
necessary. To do so switch the device off. Remove the battery and apply the chain brake.
FILLING WITH CHAIN OIL
CAUTION!
• Only add environmentally friendly, good quality
chain lubricating oil to the chain saw.
• Do not add used oil. Used oil can cause skin cancer
with extended and repeated skin contact, and is
damaging to the environment!
Used oil does not have the necessary lubricating
characteristics and is unsuitable for chain
lubrication.
• An oil other than the recommended oil can cause
damage to the rail, chain and lubrication system.
• Make sure that no dirt gets into the oil tank.
• Avoid oil spillages. Always wipe up spilled oil.
• Unscrew the oil tank cap.
• Carefully add the chain lubricating oil until it reaches
the top mark on the oil level indicator. Oil tank capacity: max. 220 ml
• Screw the oil tank cap on tightly by hand.
Original Instructions
2020/02
1
Fig.1
Fig.2
Fig. 3
Before starting the equipment
Caution! Do not fit the battery untill the equipment
has been fully assembled and
all the settings have been actuated. Always wear protective gloves when working on the equipment
to protect yourself against injury. Carefully unpack all parts and check that they are complete.
Original Instructions
2020/02
1
Fig.1
Fig.2
Fig. 3
Before starting the equipment
Caution! Do not fit the battery untill the equipment
has been fully assembled and
all the settings have been actuated. Always wear protective gloves when working on the equipment
to protect yourself against injury. Carefully unpack all parts and check that they are complete.
Original Instructions
2020/02
1
NOTE
:
The tension of a new chain must be checked after a few minutes in operation, and
adjusted if necessary. To do so switch the device off. Remove the battery and apply the chain
brake.
Filling with chain oil
CAUTION!
• Only add environmentally friendly, good quality chain lubricating oil to the chain saw.
• Do not add used oil. Used oil can cause skin cancer with extended and repeated skin contact, and
is damaging to the environment! Used oil does not have the necessary lubricating characteristics
and is unsuitable for chain lubrication.
• An oil other than the recommended oil can cause damage to the rail, chain and lubrication system.
• Make sure that no dirt gets into the oil tank.
• Avoid oil spillages. Always wipe up spilled oil.
• Unscrew the oil tank cap.
• Carefully add the chain lubricating oil until it reaches the top mark on the oil level indicator. Oil
tank capacity: max. 220 ml
• Screw the oil tank cap on tightly by hand.
Commissioning
Chain brake
WARNING!
Always check that the chain brake is working properly before use. If not, do not use the chainsaw
and have it repaired by a qualified specialist or a specialist workshop.
The chain saw is equipped with protective equipment activated by a chain brake, which brings the
chain to a standstill within a fraction of a second in the event of kickback. With kickback, the chain
brake will be trigged automatically through the contact of the hand guard with the left hand.
Therefore, always hold the chainsaw tight in both hands.
Manual activation of the chain brake
Original Instructions
2020/02
1
3.Place the guide bar with the elongated hole on the stud bolt and guide bolt on the chainsaw.
Run the saw chain around the chain wheel.
4. (1)Put the the chain cover’s sign and the adjust knob’s sign in the Vertical
alignment.(Fig.1)
(2) Fit the chain cover. Tighten the handwheel clockwise for fastening the rail and chain
cover.(Fig.2)
(3)The adjust knob adjusting the chain tension.(Fig. 3)
The saw chain must not sag, although it should be possible to pull it 1-2 millimetres away from
the guide bar in the centre of the guide bar.
Original Instructions
2020/02
1
3.Place the guide bar with the elongated hole on the stud bolt and guide bolt on the chainsaw.
Run the saw chain around the chain wheel.
4. (1)Put the the chain cover’s sign and the adjust knob’s sign in the Vertical
alignment.(Fig.1)
(2) Fit the chain cover. Tighten the handwheel clockwise for fastening the rail and chain
cover.(Fig.2)
(3)The adjust knob adjusting the chain tension.(Fig. 3)
The saw chain must not sag, although it should be possible to pull it 1-2 millimetres away from
the guide bar in the centre of the guide bar.
