6 Operating status messages
BU 0540 EN-1516
55
Switch-on block messages
Display in the
SimpleBox /
ControlBox
Reason:
Text in the ParameterBox
Cause
•
Remedy
Group
Details in
P700 [-03]
Pos: 483 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebszustand/Stör meldung en (Auflistung)/Infor mation I000_01 [SK 180E ... SK 5xxE] @ 2\mod_1347457775195_388.docx @ 47347 @ @ 1
I000
0.1
Disable voltage from IO
If the function "disable voltage"is parameterised, input (P420
/ P480) is at Low
•
Set "input High"
•
Check signal cable (broken cable)
0.2
IO fast stop
If the function "fast stop"is parameterised, input (P420 /
P480) is at Low
• Set "input High"
• Check signal cable (broken cable)
0.3
Block voltage from bus
•
For bus operation (P509):
control word Bit 1 is
"Low"
0.4
Bus fast stop
• For bus operation (P509):
control word Bit 2 is
"Low"
0.5
Enable on start
Enable signal (control word, Dig I/O or Bus I/O) was already
applied during the initialisation phase (after mains "ON", or
control voltage "ON"). Or electrical phase is missing.
•
Only issue enable signal after completion of
initialisation (i.e. when the FI is ready)
•
Activation of "Automatic Start" (P428)
0.6 – 0.7
Reserved
Information message for PLC
see supplementary
instructions
Pos: 484 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebszustand/Stör meldung en (Auflistung)/Infor mation I000_02-Erg änzung 08 und 09 [SK 180E ... SK 5xxE] @ 10\mod_1455725649528_388.docx @ 306332 @ @ 1
0.8
Right direction blocked
Switch-on block with inverter shut-off activated by:
P540
or by "Enable right block"
(P420
= 31, 73) or "Enable
left block" (
P420
= 32, 74),
The frequency inverter switches to "Ready for switching on"
status
0.9
Left direction blocked
Pos: 485 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebszustand/Stör meldung en (Auflistung)/Infor mation I006 [SK 180E ... SK 5xxE] @ 2\mod_1347457929759_388.docx @ 47372 @ @ 1
I006
6.0
Charging error
Charging relay not energised, because:
•
Mains / link voltage too low
•
Mains failure
•
Evacuation run activated ((P420) / (P480))
Pos: 486 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebszustand/Stör meldung en (Auflistung)/Infor mation I011 [SK 180E ... SK 5xxE] @ 2\mod_1347457936856_388.docx @ 47397 @ @ 1
I011
11.0
Analog Stop
If an analog input of the frequency inverter or a connected
IO extension is configured to detect cable breaks (2-10V
signal or 4-20mA signal), the frequency inverter switches to
the status "ready for switch-on" if the analog signal
undershoots the value
1 V
or
2 mA
This also occurs if the relevant analog input is
parameterised to function "0" ("no function").
• Check connections
Pos: 487 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebszustand/Stör meldung en (Auflistung)/Infor mation I014 "reser viert" [SK 200E ... SK 5xxE] @ 2\mod_1347457944329_388.docx @ 47422 @ @ 1
I014
14.4
Reserved
Error message for POSICON
see supplementary
instructions
Pos: 488 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebszustand/Stör meldung en (Auflistung)/Infor mation I018 "reser viert" [SK 2xxE/ SK 5xxE] @ 2\mod_1347457946544_388.docx @ 47447 @ @ 1
I018
18.0
Reserved
Information message for "Safe Stop" function
see
supplementary instructions
Pos: 489 /Anleitungen/El ektr oni k/FU und Starter/7. T echnische D aten/!T echnische Daten (Ü berschrift) @ 0\mod_1328183045569_388.docx @ 13960 @ 1 @ 1
