manualshive.com logo in svg

Nonin 7500FO, Operator'S Manual, Page: 42 / 42

Share
Download
Nonin 7500FO Operator'S Manual Download Page 42

36

Technical Information

 

Altitude (Operating):

Up to 4,000 meters (13,123 feet)

Hyperbaric Pressure: Up to 4 atmospheres

Power Requirements:

Mains: 100-240 VAC 50-60 Hz

DC Input: 12 VDC 1.5A AC adapter (in MR use battery 

operation only)

Internal Power:

Battery: 7.2 volt NiMH battery pack

Operating Life (fully charged battery): 30 hours minimum

Operating Life (when using 5V, 250 mA accessory

power supply [Pin 9]): 10 hours

Storage Life: 27 days minimum

Recharge Rate: 4 hours maximum

Dimensions:

Approximately 219 mm (8.6”) W x 92 mm (3.6”) H x 
142 mm (5.6”) D 

Weight:

Approximately 900 grams (2 lbs) with battery

Warranty:

3 years

Classification per ANSI/AAMI ES60601-1 and CAN/CSA-22.2 No. 60101-1:

Type of Protection: Internally powered (on battery power). 

Degree of Protection: Type BF-Applied Part

Mode of Operation: Continuous

Enclosure Degree of Ingress Protection:    

IPX2

Analog Outputs:

SpO

2

 Output Range: 0-1 VDC (0-100% SpO

2, 

1.27 VDC (no data)

Pulse Rate Output Range: 0-1 VDC (0-300 BPM), 

1.27 VDC (no data)

Event Marker: 0 V (no event), 1 V (event occurred)

Accuracy: ±2% (SpO

2

), ±5% (Pulse Rate)

Load Current: 2 mA maximum

Summary of Contents for 7500FO











































Reviews:

No comments