background image

14 

 

along the underside of the belt. If there is no lubricant residue on your fingers lubrication is 
needed.  

To add lubrication to the walking belt. Remove the key and UNPLUG THE POWER CORD. Lift 
the walking belt in the centre from the running board. Add 10 ml of lubricant to the running 
board. Turn the treadmill on using easy mode and let it run for 10 mins at 12 kph. Repeat the 
process until there is an even film of lubricant on the walking belt 

If the walking belt is off centre, or slowing when walked on or slips, remove the key and 
UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn 
the left idler roller screw clockwise ½ of a turn; if the walking belt has shifted to the right, turn 
the left idler roller screw counter clockwise 1/2 of a turn. Be careful not to overtighten the 
walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few 
minutes. Repeat until the walking belt is centred. 

 

 

 

If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER 
CORD. Using the hex key, turn both idler roller screws clockwise, 1/4 of a turn. When the 
walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 
to 3 inches (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centred. 
Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few 
minutes. Repeat until the walking belt is properly tightened. 

If the walking belt is overtightened, treadmill performance may decrease and the walking belt 
may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, 
turn both idler roller screws counter clockwise, 1/4 of a turn. When the walking belt is 
properly tightened, you should be able to lift each edge of the walking belt 2 to 3 inches. (5 to 
7 cm) off the walking platform. Be careful to keep the walking belt centred. Then, plug in the 
power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking 
belt is properly tightened. 

Symptom 

Possible Causes 

Solution 

Console screen not 

displaying anything 

The power cord is not connected 

Connect power cord 

The power switch is off 

Turn on power 

switch 

A problem with the 
communication wire 

Connect or replace 
communication wire 

Treadmill walking belt 

not working smoothly 

Walking belt is too tight 

Loosen walking belt 

Walking belt is too loose 

Tighten walking belt 

Obstruction 

Remove obstruction 

 

4.

 

Connect the signal wires between 

the console base and console. Ensure 
all wires are cleared away from the 

edges before lowering console onto 

base. 

 

 

 

5.

 

Remove the 3 x M6*15 screws from 

the back of the console. Make sure 

not to discard them. 

Place the console inside the console 

base. Ensure not to pinch or crush the 
signal wires. 

Use the 3 x M6*15 screws to fasten 

the console back onto the console 

base. 
 

 

 

 

6.

 

Place the base frame covers in 

place. 

Use the M4*15 screws to fasten the 
covers to the base frame. 

 

 

Summary of Contents for Run 8.0











Reviews: