background image

When the control board is powered, the lights “ l.e.d. are situated in the outputs, they are switched on when on the output

there is a closed contact to the common.

Normally the 

red l.e.d

. in the inputs 

“Closing limit switches” (FCC) , “opening limit switches”(FCA), STOP, FOTO

 

are always 

SWITChED ON.

Normally the 

green l.e.d.

 in the inputs 

START and PEDONALE 

(partial opening) are 

switched OFF

2.5  Description of the connections

4

230 Vac Neutral

1

230 Vac electrical power supplì 50 Hz Neutral

EARTH

2

EARTH

230 Vac Phase

3

230vac electrical power supply 50 Hz Phase

Lamp

4

Outputs for LAMP (flashing light electronic card) or 230 VAC COURTESY LIGHT

Lamp

5

M  1  Com

6

Output for the connection of motor 1 COMMON POLE M 1

M 1 Opening

7

Output for the connection of motor 1 POLE OPEN MOTOR 1

M 1 Closing

8

Outputs for connections motor no.1 pole CLOSE

M  2  Com

9

Output to connect motor no.2 pole common M2

M 2 Opening

10

Output to connect motor no.2 pole OPEN M2

M 2 Closing

11

Output to connect motor no.2 pole CLOSE

FCC  M2

12

Input Closing limit switches motor no.2

FCA  M2

13

Input Opening Limit Switches 2

FCC  M1

14

Input for Closing limit switches of motor no.1

FCA  M1

15

Input for opening limit switches of Motor 1

Photocells  A

16

Input Photocell A , working only by closing (see chapter 2.3)

START

17

Input for step-by-step function START

24Vac

18

Output for 24 Vac

24Vac / 12Vac

19

Output for electrical lock 12 Vac 50 Hz 1A

12Vac Lock

20

Output for electrical lock 12 Vac 50 Hz 1A

STOP

21

Pedestrian Stop input

PEDONALE

22

Input for step-by-step function PEDESTRIAN partial opening

Photocells  B

23

Input for photocells B working in Closing and in opening (see chap. 2.3)

Common 1

 -

24

Common for all inputs: services, Securities, coaxial antenna cable sock.

A

25

Input for antenna (antenna cable)

light or lamp

26

Contact for Light or LAMP (without electronic card)

light or lamp

27

Contact for Light or LAMP (without electronic card)

PHOTOTEST

28

Output TEST FOR PHOTOCELL 12 Vac

12Vac

29

Output 12Vac

24Vdc +

30

Output 24Vdc +

Comm.

  24Vdc  -

31

Output 24Vdc - Common for inputs: services and safety

Summary of Contents for START-S4XL















Reviews: