Nokia Remote Camera User Manual Download Page 8 | Manualshive

Page: 8 / 62

background image

I n t r o d u c t i o n

8

Copyright © 2005 Nokia. All rights reserved.

■

Battery information

The Nokia Remote Camera contains a back-up battery which is used
when there is a mains power cut. Therefore, the camera is not switched
off during a mains power cut, unless the back-up battery runs out.

Batteries and power supply

Check the model number of any power supply before use with this
device. This device is intended for use when supplied with power from
the Nokia power supply AC-12.

Warning:

Use only batteries, power supplies, and

enhancements approved by Nokia for use with this particular
model. The use of any other types may invalidate any approval
or warranty, and may be dangerous.

For availability of approved enhancements, please check with your
dealer.

When you disconnect the power cord of any enhancement, grasp and
pull the plug, not the cord.

Your device and its enhancements may contain small parts. Keep them
out of reach of small children.

Always switch the device off and disconnect the power supply before
removing the battery.

Charge and discharge

The back-up battery can be used hundreds of times but it will eventually
wear out. When the usage time is noticeably shorter than normal, buy a
new battery. Use only Nokia approved batteries.

If left unused, a fully charged battery will lose its charge over time.
Temperature extremes can affect the ability of your battery to charge.

Use the battery only for its intended purpose. Never use any charger or
battery that is damaged.

Do not short-circuit the battery. Accidental short-circuiting can occur
when a metallic object such as a coin, clip, or pen causes direct
connection of the positive (+) and negative (-) terminals of the battery.
(These look like metal strips on the battery.) This might happen, for

«
...
6
7
8
9
10
...
»

Summary of Contents for Remote Camera































































Reviews:

No comments

Related manuals for Remote Camera

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 15

DMC-TZ3A - Lumix Digital Camera

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 64

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 225

DMC-FX30A - Lumix Digital Camera

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 24

Brand: Samsung Pages: 22

GX-20 - Digital Camera SLR

Brand: Samsung Pages: 158

Brand: Samsung Pages: 100

Brand: Samsung Pages: 98

Brand: Samsung Pages: 186

Galaxy Camera EK-GC100

Brand: Samsung Pages: 178

Galaxy Camera EK-GC100

Brand: Samsung Pages: 2

Brand: Samsung Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands