manualshive.com logo in svg

Nokia M1112, Administrator'S Manual

Share
Download
Nokia M1112 Administrator'S Manual Download Page 55

M1112 Administrator Manual

E

 Copyright Nokia Networks Oy

C33907001SE_00

 5-20

5.3.7

Save Config page

When you change the configuration, all configuration changes are
activated immediately without restart/reload. However, the
configuration will not be saved into the nonvolatile memory. If M1112
is restarted or powered down without saving the configuration, the old
configuration will be restored. Clicking the Save configuration button
saves the configuration into the nonvolatile memory and the old
configuration cannot be restored through the web interface.

Figure 5-11

Save Config page

5.4

Command line interface (CLI)

M1112 can be managed locally through a command line interface
(CLI). The local command line interface is accessed through the local
management console on the back panel. The local management
console interface is an asynchronous V.24/V.28 character-based
interface with  the following configuration:

Summary of Contents for M1112














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands