manualshive.com logo in svg

Nokia M1112, Administrator'S Manual

Share
Download
Nokia M1112 Administrator'S Manual Download Page 105

M1112 Administrator Manual

E

 Copyright Nokia Networks Oy

C33907001SE_00

Glossary-2

PPTP

Point-to-point tunneling protocol

PWR

Power

RAN

Remote access node

RFC

Request for comments

STA

Status

TCP

Transmission control protocol

UBR

Unspecified bit rate

VCC

Virtual channel connection

VCI

Virtual channel identifier

VPI

Virtual path identifier

WWW

World Wide Web

Terms

10Base-T

10 Mbit/s Ethernet specification using two pairs of twisted cabling.
10Base-T is a part of the IEEE 802.3 specification.

ATM access network

An access network where traffic from the subscribers is multiplexed
and forwarded using ATM technology.

bridge

A device that connects two or more physical networks and forwards
packets between them. Bridges can usually be made to filter packets,
that is, to forward only certain traffic.

command line interface

Character-based man-machine interface where a command line end-
ing with <CR> character is used to configure a device. The device in-
terprets the command and returns a character-based response.

Summary of Contents for M1112














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands