Nokia 6125 RM-178 Service Manual Download | Manualshive

Page: 24 / 42

background image

Training and Vendor Development

CMO Service Operations

Multimedia Creation & Support

CONFIDENTIAL

15.Dec.2006

24

Service Manual 6125 RM-178 /6136 RM-106/-199

Copyright © 2006 NOKIA Corporation. All rights reserved.

Approved 4.0

MGR

Page

(42)

LOWER BLOCK DISASSEMBLY

11.

1. Needed tools.

2. Cover the B-Upper Assembly window with protective film.

3. Unlock the Battery Cover and remove it.

4. Cover the LCD Window with protective film.

5. Release the snaps on the left side of the Antenna Cap with

the SRT-6.

6. Turn the phone over and release the snap in the middle.

«
...
22
23
24
25
26
...
»

Summary of Contents for 6125 RM-178











































Reviews:

No comments

Related manuals for 6125 RM-178

Brand: Panasonic Pages: 24

Brand: 2N Pages: 8

Brand: 2N Pages: 83

Brand: Aastra Pages: 9

Brand: Yealink Pages: 4

Brand: Yealink Pages: 148

Brand: Yealink Pages: 2

Brand: Yealink Pages: 131

Brand: Yealink Pages: 159

Brand: Yealink Pages: 9

Brand: Samsung Pages: 139

Brand: Linksys Pages: 5

Brand: B Mobile HK Pages: 43

Brand: SBS Pages: 52

Brand: Yezz Pages: 29

Brand: Aastra Pages: 96

SolutionStation 2W

Brand: Polycom Pages: 46

Brand: Zartek Mobile Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands