Nokia 6125 RM-178 Service Manual Download | Manualshive

Page: 15 / 42

background image

Training and Vendor Development

CMO Service Operations

Multimedia Creation & Support

CONFIDENTIAL

15.Dec.2006

15

Service Manual 6125 RM-178 /6136 RM-106/-199

Copyright © 2006 NOKIA Corporation. All rights reserved.

Approved 4.0

MGR

Page

(42)

19. Open the Micro Coax Cable Assembly connector with the

SS-93.

20. Lift up the UI-Module with the SS-93. Note the guide pin.

21. Remove the UI-Module and turn it over.

22. Cover the LCD AM with protective film.

23. Open the LCD AM connector with the SS-93.

24. The LCD AM is glued to the UI-Module. Use the SS-93 and start

releasing the adhesive bond from the connector side.

«
...
13
14
15
16
17
...
»

Summary of Contents for 6125 RM-178











































Reviews:

No comments

Related manuals for 6125 RM-178

Brand: Palm Pages: 52

Brand: TCL Pages: 34

Brand: TCL Pages: 38

Brand: TCL Pages: 26

Brand: TCL Pages: 10

Brand: Yealink Pages: 6

Brand: Yealink Pages: 8

Brand: AGM Pages: 11

Brand: Rath Pages: 8

Brand: Alcatel Pages: 2

Brand: Snom Pages: 2

Brand: Archos Pages: 75

Brand: Konftel Pages: 8

Brand: T-Mobile Pages: 212

Brand: Crestron Pages: 422

Brand: iPRIMUS Pages: 2

8600 - Cell Phone - CDMA2000 1X

Brand: Audiovox Pages: 74

Brand: Avvio Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands