background image

-5-

  9. Place 

Weight Stack Supports

 (26) over holes in 

Rear Base

,

place 

Rubber Cushions

 (AI) over holes in 

Weight Stack

Support

 and slide the 2 - 

Guide Rods

 (9) through them into

Rear Base

.

NOTE:

  

For improved performance, we recommend

you apply a silicone lubricant to the guide rods prior to their
installation

.

10. By pulling the 

Guide Rods

 towards you, you can slide the

fourteen 

Weight Stack Plates

 (31) on to the 

Guide Rods

 as

shown.

11. Slide the 

Selector Rod

 (23) onto the 

Weight Stack Plates

.

12. Slide the 

Shaft Collars

 (AK) and the 

Guide Rod Retainers

(AJ) over the 

Guide Rods

 as shown.  Position the 

Guide Rods

in the 

Top Plate Assy

.  Move the 

Shaft Collars

 & 

Guide Rod

Retainers

 up the 

Guide Rods

 until the flange of the 

Guide

Rod Retainers

 rest against the 

Top Plate Assemble

.  Tighten

the set screw in the 

Shaft Collars

.  Tighten the bolts holding

the 

Top Plate Assy

 to the 

Main Upright

.

13. Loosely bolt 

Weight Stack Shroud

 (14) & 

Wt Stack Front

Shroud R&L

 (25) to 

Rear Base

 using bolting shown.  

Shrouds

(25) must be installed on the outside of 

Shroud

 (14).

14. Install 

Edge Trim

 (AH) on 

Weight Stack Shroud

 & 

Wt

Stack Front Shrouds

.  Tighten bolts previously left loose.

15. Install 

1-1/2" Plastic Caps

 (AE) & 

2" Plastic Caps

 (AF) where

shown.

AJ

23

31

AE

AE

AF

AH

14

AI

26

9

N

4 Places

O

4 Places

2 Places

AK

Summary of Contents for MG-GRANITE GRANITE6










Reviews: