background image

Operation and Maintenance Manual                                                                 

Second Edition

 

 

32 

                                      Maxiton  GTJZ

 

 

Result: The machine should shut off and no machine 

functions should operate.  

The ground Emergency Stop 

button will stop all machine operation, even if the  

  

B-8 Test the Ground Control 

Override  

A properly functioning ground control override is 

essential to safe machine operation. The ground 

control override function is intended to allow ground 

personnel to operate the machine from the ground 

controls whether or not the Emergency  

Stop button on the platform controls is in the ON or 

OFF position. This function is particularly useful if the 

operator at the platform controls cannot return the 

boom to the stowed position.  

1 Push in the platform Emergency Stop button to 

the OFF position.  

2 Start the machine from the ground controls.  

3 Operate each boom function through a partial 

cycle.  

Result: All boom functions should operate.  

  

B-9 Test the Safety Envelope   

Testing the machine safety envelope is critical to safe 

machine operation. If the boom is allowed to operate 

when a safety switch is not functioning correctly, the 

machine stability is compromised and may tip over.  

1 Machine not Level sensor  

Machine not Level exceed 3

°

, the alarm sound and 

the boom is not raise.  

Machine can’t into uneven groud when it is 

working.Not before the ground into arms frame to 

pack up. 

 

 

 

 

 

 

 

 

B-10 Test the Horn

 

 

A functional horn is essential to safe machine 

operation. The horn is activated at the platform controls 

and sounds at the ground as a warning to ground 

personnel. An improperly functioning horn will prevent 

the operator from alerting ground personnel of hazards 

or unsafe conditions.  

1 Turn the key switch to platform control and pull out 

the Emergency Stop button to the ON position at 

both the ground and platform controls.  

2 Push down the horn button at the platform controls.  

Result: The horn should sound.  

  

If necessary, the horn can be 

adjusted to obtain the loudest volume by turning the 

adjustment screw near the wire terminals on the horn.

  

 

B-12 Test machine high and low 

speed’s options  

Proper execution of the high and low speed’s options is 

critical for proper and safe operation. Low speed (turtle 

sign) option allows the operator to operate the boom 

and / or drive functions at the same time. This button 

remains at the low speed option.  

  

High speed (rabbit symbol) option should be used 

when the machine is operating normally. This selection 

button activates high speed option.  

  

1. Rotate the selector switch to the ground controller. 2. 

Let the emergency stop switches to the "ON" position 

of the ground and the platform controllers.   

3.Start the machine from the ground controller.  

4.Pull the selection button  

  

Result: The machine becomes high speed condition  

  

5 Pull the selection button again  

  

Summary of Contents for Maxiton GTJZ Series











































Reviews: