nitedevil CAM190 Manual Download Page 5

  www.nitedevil.com

                          Doc XCAM190

 

NiteDevil Traditional Wide Dynamic

Email:

[email protected]

Last Revised: 03/011/2010

NOTE:

 All menu items with the

 icon require the SET button to be depressed.

               If  -  - - is displayed then feature is unavailable on this camera.

SHUTTER  AUTO, 1/50, FLK, 1/250, 1/500, 1/2000, 1/5000, 1/10000, 1/100000, x256, x128, x64, x32, x16, x8,
x4, x2

Select EXPOSURE by using UP & DOWN buttons and then select desired mode.

AUTO

Select this mode to control the shutter speed automatically.

FLK

Select this mode if flickering occurs on screen.

BRIGHTNESS  (1 – 100)

  You can control the brightness by using the LEFT & RIGHT buttons in Manual lens

mode. If using a DC lens, switch LENS to manual, adjust brightness, then return to LENS and select DC.

AGC  OFF /  LOW / MIDDLE / HIGH

Set AGC from low to high gain. Note that the higher the gain level, the brighter the screen but the higher noise level.
Note that if AGC shows - - - then RESET the camera.

SENSE-UP  OFF / AUTO

x2 / x4 / x8 / x16 / x32 / x64 / x128 / x256

When it is dark the camera automatically detects the light level and tries to compensate by maintaining a clear picture.

OFF

The option is deactivated when the OFF option is selected or when AGC is OFF or DAY&NIGHT is OFF.

AUTO

You can adjust brightness by increasing/decreasing the shutter speed (x2 ~ x256)

Note that noise can be amplified as SENSE-UP in increased.

Menu Settings

1

.  LENS

MANUAL

2.  EXPOSURE
3.  WHITE BAL

AWB

4.  DAY NIGHT

AUTO

5.  3DNR

ON

6.  SPECIAL

7.  ADJUST

8.  RESET

9.  EXIT

LENS

When the SETUP menu screen is displayed, select LENS by
using the UP & DOWN buttons so that the arrow selects
LENS.

Select the connected type by using the LEFT & RIGHT
buttons.

Selecting MANUAL selects manual lens

Selecting DC selects Auto Iris Lens. When MANUAL is
selected you can select the brightness control by pressing the
SET button. Set range between 0 ~ 100. Then select DC.

MENU SETTINGS

1.  LENS

MANUAL

2.  EXPOSURE

3.  WHITE BAL

AWB

4.  DAY NIGHT

AUTO

5.  3DNR

ON

6.  SPECIAL

7.  ADJUST

8.  RESET

9.  EXIT

EXPOSURE

SHUTTER

1/250

BRIGHTNESS

-  -  -

AGC

MIDDLE

SENSE-UP

OFF

BLC

OFF

D-WDR

INDOOR

RETURN

RET

Summary of Contents for CAM190














Reviews: