23
ninjakitchen.com
22
ninjakitchen.com
CARE & MAINTENANCE
CLEANING
Hand-Washing
Wash containers, lids, discs, and blade
assemblies in warm, soapy water. Use a
dishwashing utensil with handle to avoid direct
contact with the blades. Exercise care when
handling the blade assembly as the blades are
sharp. Thoroughly rinse and air-dry all parts.
Dishwasher
Containers, lids, discs and blade assemblies
are dishwasher safe. Ensure the blade
assembly and lid are removed from the
container before placing in the dishwasher.
Motor Base
Unplug the motor base before cleaning.
Wipe motor base with a clean, damp cloth.
DO NOT
use abrasive cloths, pads, or
brushes to clean the base.
STORING
To purchase a storage
case to house most
attachments that come
with this unit, visit
ninjaaccessories.com.
Store the Hybrid Edge™
Blades Assembly with the single-serve cup
and the storage lid with the XL bowl.
For cord storage, wrap cord with hook-and-
loop fastener near the back of the motor
base.
DO NOT
wrap the cord around the
bottom of the base for storage.
DO NOT
store blended or unblended
ingredients in the cup or XL Bowl with the
blade assembly attached.
DO NOT
stack items on top of the
containers. Store any remaining attachments
alongside the unit or in a cabinet where they
will not be damaged or create a hazard.
RESETTING THE MOTOR
This unit features a unique safety system
that prevents damage to the motor and
drive system should you inadvertently
overload it. If the unit is overloaded, the
motor will be temporarily disabled. Should
this occur, follow the reset procedure below.
1
Unplug the unit from the electrical outlet.
2
Allow the unit to cool for approximately
15 minutes.
3
Remove the container’s lid and blade
assembly. Empty the container and ensure
no ingredients are jamming the blade
assembly.
IMPORTANT:
Ensure that maximum
capacities are not exceeded. This is the most
typical cause of appliance overload.
If your unit needs servicing, please call
Customer Service at 1-877-646-5288. So we
may better assist you, please register your
product online at
registeryourninja�com
and
have the product on hand when you call.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments,
visit
ninjaaccessories�com
.
Single-Serve Cup:
Fill halfway with warm water and
add 1 small drop dish soap. Install
blade assembly.
3
Install the container on the motor base.
Select BOWL, then press START/STOP.
4
Once program is complete, thoroughly
rinse container and blade assembly
under warm, soapy water.
1 SMALL DROP OF DISH SOAP
FILL WATER HALFWAY
NOTE:
For best results, use a dishwasher
to remove stuck-on ingredients.
USING THE BLENDER
FOR STUCK-ON INGREDIENTS
1
After processing, immediately clean the
container and blade assembly under
warm, soapy water.
2
Depending on the container, fill with soap
and water according to the following
instructions:
72-ounce Pitcher & Flat Lid:
With the dough or stacked blade
assembly installed, fill with warm water
up to DOUGH MAX line and add 1 or 2
small drops dish soap. Secure flat lid, and
ensure the pour spout is securely closed.
XL Bowl:
Fill with warm water up to top of built-in
tamper and add 1 or 2 small drops dish
soap. Install blade assembly.
FILL WATER TO TOP
OF BUILT-IN TAMPER
1 OR 2 SMALL DROPS
OF DISH SOAP
NOTE:
If using the XL bowl, twist the
built-in tamper counterclockwise
continuously
while cleaning.
1 OR 2 SMALL DROPS OF DISH SOAP
FILL WATER TO
DOUGH MAX LINE
NOTE:
For best results, use a dishwasher
to remove stuck-on ingredients.
NOTE:
The built-in tamper in the
XL bowl is not removable.
