7
ninjakitchen.com
6
ninjakitchen.com
1
Programmable Digital Clock
2
Hour & Minute Buttons
3
Stay Warm Indicator/Button
4
Delay Brew Button
5
Multi-Serve Dial
a Cup
b XL Cup
c Travel Mug
d XL Multi-Serve
e Half Carafe
f Full Carafe
6
Custom Brews
Classic Brew
Rich Brew
Over Ice Brew
7
Signature Brew
Specialty Brew
8
Drip Stop Indicator
9
Intelligent Clean Cycle
Indicator/Button
10
Power Button
PREPARING YOUR NINJA® SPECIALTY COFFEE MAKER FOR USE
CONTROL PANEL
1
When the unit is plugged in, the clock
will flash on the control panel to indicate
that the time has not been set.
2
Press the hour (H) or minute (M) button
until you reach the current time. The AM or
PM indicator will illuminate on the left side
of the display as you are setting the time.
3
After 5 seconds, the clock will stop
flashing and the clock will be set.
SETTING THE CLOCK
HIGH-ALTITUDE CALIBRATION BREW
NOTE:
If the clock stops flashing and
does not display the correct time of
day, pressing the hour (H) or minute (M)
button at any time will cause the clock
to flash again. You can now reprogram
the correct time by following the
previous steps.
NOTE:
If you unplug the coffee maker or
in the event of an extended power loss,
you will need to reset the clock the next
time the coffee maker is plugged in.
(OPTIONAL, BUT RECOMMENDED FOR USERS IN HIGH-ALTITUDE AREAS)
Because water boils at lower temperatures at higher altitudes, running a calibration cycle
before your first brew allows the unit to detect the boiling point of water at your location.
Running a calibration cycle will help deliver a consistent brew each time.
1
Fill the water reservoir up to, but not exceeding, the Max Fill line.
2
Place the empty filter holder into the brew basket, and an empty vessel in the machine.
3
Press and hold both
CLASSIC
and
OVER ICE
until clock displays
CAL
.
4
A calibration cycle will begin. When complete, the unit will beep and
End
will appear on
the clock display. Discard the water in the vessel.
NOTE:
Pressing the CLASSIC, OVER ICE, or Power button will cancel the calibration cycle.
Remove all packaging material and stickers from the coffee maker.
Wash the water reservoir, carafe, and removable filter holder in warm, soapy water with
a soft cloth. Rinse parts and dry thoroughly.
Before first use, prime the system by running two Full Carafe, Classic brew cycles with
water only. After each cycle is complete, discard the water. For detailed instructions,
refer to the Priming Your Ninja Specialty Coffee Maker section.
PLEASE KEEP THIS IMPORTANT SAFEGUARD IN MIND WHEN USING THE APPLIANCE:
DO NOT
run the appliance without water.
4
5d
5f
5e
10
1
3
7
8
9
5a
5b
2
6
5c
5
SCA CERTIFIED HOME BREWER
The Specialty Coffee Association (SCA) recognizes home brewers that meet
their longstanding rigorous technical requirements. These requirements are
based on decades of industry knowledge and research by the Coffee Brewing
Center. All SCA Certified Home Brewers have met these requirements, which
are based generally on proper water temperature, brewing time, and ability to
brew within the SCA Golden Cup recommendations
If a brewer passes all of the tests in the certification procedure, as conducted by the SCA,
that brewer will be eligible to be recognized as an exemplary home brewer and join the
short list of SCA Certified Home Brewers.
This coffeemaker has been certified by the SCA to meet their Golden Cup Standard,
designed for optimal extraction and strength. SCA Certification testing was performed
using the Half Carafe and Full Carafe on Classic brew using the Low warming plate
setting. Testing used the following ground coffee measurements: 55 grams for a Half
Carafe and 77 grams for a Full Carafe. When using the Ninja Smart Scoop™, this would
be 4 heaping big scoops for a Half Carafe and 6 heaping big scoops for a Full Carafe.
