Nilfisk-Advance Liberty SC60 Instructions For Use Manual Download Page 27 | Manualshive

Page: 27 / 54

background image

11/2020

A - 27

56091229 - Nilfisk Liberty SC60

ENGLISH - A

INSTRUCTIONS FOR USE

TEACH ROUTE FOR AUTONOMOUS MODE

The machine needs to be taught the exact route to be traveled while

cleaning in autonomous mode before the route can be run. This route is

saved along with scrub settings to use while cleaning.

1 Follow the instructions in

“Starting the Machine”

section. Once the

main screen appears press “Teach”.

2 The touchscreen display will show the view of the right side camera.

Manually drive the machine to the Home Marker until it is at a

distance of 2 feet (0.6 m) and visible within the display. The Home

Marker will be scanned automatically. A confirmation message will

display after the Home Marker is successfully scanned.

NOTE:

If the machine can not scan the Home Marker the display

will show an error message with steps to correct the issue (i.e.

Home Marker may be rotated).

«
...
25
26
27
28
29
...
»

Summary of Contents for Liberty SC60























































Reviews:

No comments

Related manuals for Liberty SC60

Brand: Pacific Pages: 20

Nautilus MX3-500HE

Brand: Hydro-Force Pages: 57

Brand: GermAwayUV Pages: 7

Nautilus Extreme MXE-200

Brand: Hydro-Force Pages: 55

TrafficJet Purex

Brand: Avery Dennison Pages: 6

Brand: COMAC Pages: 44

VORT QUADRO SUPER GB

Brand: Vortice Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands