Nilfisk-Advance Captor 4300B Instructions For Use Manual Download Page 16

Page: 16 / 60

A-16

- FORM NO. 56041577 - Captor

™

4300B, 4800B / CR 1100B, 1200B

A-16 / ENGLISH

FILLING THE SOLUTION TANK

The solution tank

(3)

is located at the left rear corner of the machine and has a 75 gallon (284 liter) maximum capacity. Fill the tank with the proper dilution of

cleaning chemical mixed with water according to the manufacturer’s recommendations. If using a powdered chemical, mix it with water in a bucket before putting it
into the machine’s solution tank.

NOTE:

DO NOT

ll the tank past the Maximum Level on the Water Level Gauge

(24)

NOTE:

AXP/EDS machines can either be

used conventionally with detergent mixed in the tank or the AXP/EDS detergent dispensing system can be used. When using the AXP/EDS detergent dispensing
do not mix detergent in the tank, plain water should be used.

CAUTION!

Use only low-sudsing, non-

ammable, non-caustic cleaning chemicals intended for machine application.

DETERGENT SYSTEM PREPARATION AND USE (AXP/EDS MODELS ONLY)

Fill the detergent cartridge with a maximum of 2.2 gallons (8.32 Liters) of detergent.

SERVICE NOTE:

Remove the detergent cartridge from the detergent box

prior to

lling to avoid spilling detergent on the machine.

It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the detergent
name on each cartridge to avoid mixing them up. The detergent cartridge has a Magnetic Slider

(A)

on one end that needs to be set to the proper dilution ratio according to the

dilution instructions on the manufacturer’s bottle. Slide the Magnet Slider

(A)

to the appropriate location on Detergent Dilution Ratio Decal

(B)

. When installing a new cartridge,

remove the Cap

(C)

and place the cartridge in the detergent box. Install the Dry Break Cap

(D)

as shown.

The system should be purged of previous detergent when switching to a different detergent.

SERVICE

NOTE:

Move machine over

oor drain before purging because a small

amount of detergent will be dispensed in the process.

To Purge When Changing Chemicals:

Disconnect and remove the detergent cartridge.

Turn the Key Switch

(CC)

ON and press the Detergent ON/OFF Switch

(RR)

for at least 2 seconds.

NOTE:

Once activated the purge process takes 10 seconds. See

illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system.

To Purge Weekly:

Disconnect and remove the detergent cartridge. Install and connect a Cartridge

lled with clean water

Turn the Key Switch

(CC)

ON and press the Detergent ON/OFF Switch

(RR)

for at least 2 seconds.

NOTE:

Once activated the purge process takes 10 seconds. See

illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system.

The Detergent Box

(E)

has a Detergent Level Viewing Slot

(F)

for keeping track of how much detergent is remaining in the cartridge. When the detergent level is nearing the

bottom of this slot it is time to re

ll or replace the cartridge.

General Use:

The detergent (AXP/EDS) system is enabled when the Key Switch

(CC)

is turned on and reverts to the last state (Chem On or Chem Off) it was in prior to the last power down.

The current Solution Flow Rate

(VV)

and the last used Detergent Ratio

(WW)

(if in “Chem On” state) are displayed. The Status LED

(YY)

indicates the status of the system as

follows:

GREEN:

Solution not low and chemical pump ON (pumping solution and chemical)

BLINKING GREEN:

Purge has been activated

LED OFF:

Solution

ow position = 0 or solution solenoid is OFF

ORANGE:

Solution ON and Chemical OFF (pumping solution only)

BLINKING RED:

Solution low and chemical pump ON (pumping solution only)

No detergent is dispensed until the scrub system is activated and the Drive Pedal

(MM)

pushed forward. The detergent ratio can be varied by subsequently pressing the

Detergent Ratio Increment and Decrement Switches

(SS & TT)

. The detergent

ow rate increases or decreases with the solution

ow rate but the detergent ratio remains the

same unless changed. During scrubbing, the detergent system
can be turned off at any time by pressing the Detergent ON/
OFF Switch

(RR)

to allow scrubbing with water only. On AXP/

EDS models the solution

ow rate (40%-100%) is electronically

controlled and is displayed

(VV)

on the AXP/EDS display panel

as shown below.

SERVICE NOTE:

Follow the “To Purge Weekly” instructions

above if the machine is going to be stored for an extended
period of time or if you plan to discontinue use of the
detergent (AXP/EDS) system. The Display Panel

(UU)

will

display an Error Code “E1”

(XX)

in the lower left corner if the

magnetic slider circuit board

(ZZ)

becomes disconnected or

malfunctions.

revised 3/08