22
- FORM NO. 56043098 - Convertamatic
™
24, 26, 28, 32 / BA 625, 725, 825
SCRUB SYSTEM
SCRUB BRUSH DECK REMOVAL (DISC)
1
Lower the scrub deck with brushes (pads) installed. Turn the key switch off and disconnect the battery pack.
2
Lift up and remove cover and nose cone, from front of machine.
3
See Figure 2.
Separate the solution system water line
(A)
located on top of the scrub deck.
4
Unplug both of the brush motor wiring harnesses
(B)
.
NOTE:
Cable ties may need to be cut.
5
Remove the lower Hitch Pin
(C)
that secures the brush deck lift actuator to the scrub deck.
Note:
Lift up on the scrub deck to take pressure off the Pin
(C).
Service Note: It is
important that the actuator motor is not run while it is disconnected from the deck or chassis mounts. This precaution will prevent the actuator drive nut from being
misadjusted (moved out of its set speci
fi
cation).
6
Remove the Cotter Pin
(D)
and washers that attach the Upper Hitch Pin
(E)
to the machine chassis Linkage Arm
(F)
.
NOTE:
Reference Con
fi
g (A) or (B) depending on what your
machine looks like.
7
Remove the two
(G)
Hitch Pins that attach the scrub deck to the machine’s chassis Linkage Arms
(H)
. Then rotate the Arms
(H)
out of the way.
8
From the front of the machine swing the lower actuator housing forward to clear the deck mount bracket (remove the actuator on AXP™ / EDS™ models). Then slide the deck
towards the left side of the machine until Pin
(E) – Con
fi
g A
is clear of Arm
(F) – Con
fi
g A
or until Arm
(F) – Con
fi
g B
is clear of the tank bracket. Pull the deck forward away from
the machine to complete the removal.
SERVICE NOTE
: It is important that the actuator motor is not run while it is disconnected from the deck or chassis mounts. This precaution
will prevent the actuator drive nut from being misadjusted (moved out of its set speci
fi
cation).
9
To install a scrub deck, follow the above steps in reverse order.
SCRUB BRUSH LIFT ACTUATOR REMOVAL (DISC.)
1
See Figure 2.
With scrub brushes installed, lower the scrub deck, turn the key off and disconnect the battery pack.
Note:
If the lift actuator motor will not run go to step 2 and
perform the following, shim up the brush deck to remove the weight on the lower deck Actuator Pin
(C)
to remove.
2
Remove the front nose cone by
fi
rmly grasping the lower part and lifting straight up.
3
Disconnect the actuator motor wiring harness pig tail connector.
4
Remove the lower actuator mount Pin
(C). Note:
Lift up on the scrub deck to take pressure off the pin
(C).
5
Remove the Pin
(I)
from the upper actuator mount weldment and remove the motor.
6
See *Important Service Note below.
7
Reinstall in reverse order.
*Important Service Note:
After removing any actuator motor and before installing a new motor or drive nut the IN and OUT limit switches must be set (or checked) to their correct
speci
fi
cations. Reference the Electrical System in this manual for the
Actuator Drive Nut Adjustment
and follow these instructions before replacing the actuator motor.
After setting the correct actuator nut adjustments for the scrub brush lift motor, follow removal steps in reverse order to reassemble.
SCRUB BRUSH MOTOR/GEARBOX REMOVAL (DISC)
Follow the steps in the
1
Scrub Brush Deck Removal (Disc)
section.
Turn the brush deck on its back.
2
Remove the scrub brushes from the brush holders. If removing both motor/gearboxes mark the location of the holders and motors to the brush deck for proper re-assembly.
3
See Figure 3.
4
Remove the (3)
(J)
Hex Screws from the
fl
exible coupler that attaches the brush holder to the drive Hub
(K)
of the Motor/Gearbox Assembly you want to remove.
Remove the (1) Hex Screw
5
(L)
that secures the Hub
(K)
to the output shaft on the defective motor/gearbox. Then pull the hub from the shaft and save the key.
Remove the (4)
6
(M)
Screws and separate the defective Motor/Gearbox Assembly
(N)
from the scrub deck.
Re-assemble in reverse order and test for proper operation. Note: Apply a small amount of grease or a product called “Never Seize” to the gearbox output shaft when reinstalling
7
the Drive Hubs
(K).
revised 7/07
FIGURE 3
Summary of Contents for BA 625
