background image

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

9

SOURCE POWER STATUS CONNECTIONS

To properly automate home theater sources, the HT-MSU needs to “know” when the source is 
powered On or Off. There are three ways that sources are powered on:

1.  

Toggle Power: 

 A source via its remote control has one button for turning that source 

On and Off. When trying to automate such a device, you must provide the HT-MSU the 
“Power Status” as feedback using the Status connection on the HT-MSU’s top edge 
(detailed below).

2.  

Separate On and Off Power:  

A source via its remote control has one button to turn 

the source On and a different button to turn the source Off. When trying to automate 
such an IR device, you should provide the HT-MSU the “Power Status” as feedback so 
the iC2 System will act faster using the Status connection on the HT-MSU. If a source 
is to be controlled via RS232 and it has separate On and Off codes, you do not need to 
provide the HT-MSU feedback. 

3.  

Latching Power:  

Latching power is an industry term that means the source has no 

power command/s on its remote control. A latching power source may have a “hard” 
power button on the front panel. To determine if a source is latching power, push its 
“hard” power button in, take its power cord and plug it into a live AC power outlet. If it 
turns on when plugged into the outlet and turns off when unplugged from the outlet, 
it is a latching power source. Latching power sources do not need a Power Status 
connection, but you will want to do one of two things: 

a.

 Plug it into the switched outlet of the receiver, or

 

b.

 Use a Niles AC-3 Voltage Triggered Power Strip connected to one of the  

assignable 12V outputs on the HT-MSU. Use the QuickConfig Software to 
program the assigned 12V output to turn on when that source is selected. 
(See QuickConfig

 

manual for more details on programming 12V outputs.)

    Along the top edge of the HT-MSU are the source-specific status connections labeled 

SRC1 through SRC6. These RCA jacks are designed to sense either 12 Volts or video  
so the HT-MSU “knows” when the source is On or Off. You must use these connections  
if the source you are trying to automate is IR controlled and uses toggle power  
(see 

1.Toggle Power

 above). 

    If the source has a video out jack, connect the video output to the corresponding SRC 

Status RCA jack on the HT-MSU. If the source has no video output jack, you may use 
one of the Niles external-sensing devices that provides 12V output (i.e., the CS12V 
Current Sensor or the LS-1 Light Sensor) connected to the RCA Status jack.

Summary of Contents for iC2

































Reviews: