Nikon D50 Repair Manual Download Page 47

Page: 47 / 99

Ａ12

･

VBA12001-R.3668.A

Angle adjustment of Main mirror and sub-mirror

*Tools required:

1.Main mirror 45°Inspection and Adjustment

2. Sub-mirror 47.75° Inspection and Adjustment

J18037

J18362

①

Collimator (J19002)

②

Reflection mirror (J18362

）

③

Optical parallel (J18037

）

④

Hexagonal wrench

Main mirror

Eccentric pin for

the main mirror

Collimator

Bayonet

J18324

①

Collimator (J19002)

②

Sub-Mirror 45 deg. inspection tool

（

J18324

）

③

Hexagonal wrench

Sub-mirror

Eccentric pin

for the sub-

mirror

Collimator

Bayonet

* Standard:

Main mirror

Sub-mirror

Left-right

deviation

±30’ or less

　　　　＿＿　　

Up-down
deviation

±10’

+15’

～

-50'

Distortion

8’or less

Up-down

Left-right

Reference

line

Width of line indicates
deviation.

・

Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few

times.

・

Check for the up-down deviation. In case the deviation is out of standard, make an adjustment by turning the

eccentric pin with Hexagonal wrench.

・

In case the deviations of up-down and left-right are out of standard, the front plate unit or mirror unit is

regarded as malfunctioning.

・

In case of checking or adjusting only the front body, check again after assembling the front body into the rear

body.

* Note:

Summary of Contents for D50



































































































Search results

Summary of Contents for D50

Reviews:

Nikon D50, Repair Manual, Page: 47 / 99

Search results

Summary of Contents for D50

Reviews: