NIKON VISION CO., LTD.
Customer Service Department
3-25, Futaba 1-chome, Shinagawa-ku, Tokyo 142-0043, Japan
Tel: +81-3-3788-7699 Fax: +81-3-3788-7698
Printed in China (197K)/1E
CAUTIONS BEFORE USE
Please observe the following guidelines strictly so you can use the equipment properly
and avoid potentially hazardous problems. Before using this product, read thoroughly the
“SAFETY AND OPERATION PRECAUTIONS” and instructions on correct usage
accompanying the product. Keep this manual within reach for easy reference.
WARNING
This indication alerts you to the fact that any improper use ignoring the contents
described herein can result in potential death or serious injury.
CAUTION
This indication alerts you to the fact that any improper use ignoring the contents
described herein can result in potential injury or material loss.
SAFETY AND OPERATION PRECAUTIONS
Warning
•
Never look directly at the laser beam or directly at the sun when using the Nikon
Callaway id TECH.
• Do not depress the POWER button while looking into the optics from the objective side.
• Do not aim at the eye.
• Do not operate the unit with other additional optical elements, such as lenses or
binoculars. Using an optical instrument together with the Nikon Callaway id TECH
increases the danger of damaging the eyes.
• Do not disassemble the Nikon Callaway id TECH. A product that has been disassembled
is not guaranteed by the manufacturer.
• When the Nikon Callaway id TECH’s body cover is damaged, or if it emits a strange
sound due to dropping or for some other cause, immediately remove the
battery and stop using.
Cautions
• When not using the Nikon Callaway id TECH, do not push the POWER button.
• Do not leave the Nikon Callaway id TECH within the reach of small children.
• Rain, water, sand and mud should be removed from the rangefinder body surface as soon
as possible, using a soft, clean, dry cloth.
• Although the Nikon Callaway id TECH is waterproof, it is not designed for use
underwater.
• Do not swing the Nikon Callaway id TECH by its strap. It may hit someone and cause
injury.
• Do not leave the Nikon Callaway id TECH in an unstable place, as it may fall and cause
injury, or damage the equipment.
• Do not look through the Nikon Callaway id TECH while walking. You may walk into
something and get hurt.
• Do not leave the Nikon Callaway id TECH in a car on a hot or sunny day, or near heat-
generating equipment. This may damage or negatively affect it.
• Do not leave the Nikon Callaway id TECH in direct sunlight. Ultraviolet rays and
excessive heat may negatively affect or even damage the unit.
• When the Nikon Callaway id TECH is exposed to sudden changes in temperature, water
condensation may occur on lens surfaces. Do not use the product until the condensation
has evaporated.
• Do not use alcohol for cleaning the main body.
• Do not leave the polyethylene bag used for packaging within the reach of small children.
• Be careful that small children do not inadvertently swallow the eyecup. If it does happen,
consult a doctor immediately.
• If you use the rubber eyecup for a long period of time, you may suffer skin inflammation.
If you develop any symptoms, consult a doctor immediately.
• When carrying the Nikon Callaway id TECH, store it in the soft case.
• If your Nikon Callaway id TECH should fail to operate correctly, discontinue use
immediately and consult the Troubleshooting Table. If you are unable to fix the problem,
contact your local dealer for instructions on where to send it for repair.
CARE AND MAINTENANCE
Lenses
• When removing dust on the lens surface, use a soft oil-free brush.
• When removing stains or smudges like fingerprints from the lens surface, wipe the lenses
very gently with a soft clean cotton cloth or quality oil-free lens tissue.
Use a small quantity of pure alcohol (not denatured) to wipe stubborn smudges. Do not
use velvet cloth or ordinary tissue, as it may scratch the lens surface. Once the cloth has
been used for cleaning the body, it should not be used again for the lens surface.
Main body
• Clean the body surface with a soft, clean cloth and a dry cloth. Do not use benzene,
thinner, or other organic agents because they may cause discolouration or rubber
degeneration.
Storage
• Water condensation or mould may occur on the lens surface because of high humidity.
Therefore, store the Nikon Callaway id TECH in a cool, dry place.
After use on a rainy day or at night, thoroughly dry it at room temperature, then store in a
cool, dry place.
NOTES ON LITHIUM BATTERY
If handled incorrectly, batteries may rupture and leak, corroding equipment and staining
clothing. Be sure to observe the following:
• Install batteries with the + and – poles positioned correctly.
• Batteries should be removed when exhausted or during extended periods of non-use.
• Always use the same brand of battery.
• If battery fluid contacts eyes or skin, rinse well with water. If swallowed, consult a doctor
immediately.
• Do not short-circuit battery chamber terminals.
• Do not carry batteries together with keys or coins in a pocket or bag. This may overheat
and short-circuit batteries.
• Do not put batteries in fire or water. Never disassemble batteries.
• Do not charge batteries.
• Do not subject stored batteries to extremes in temperature.
• Do not subject batteries to strong vibrations or shock.
Key Features
Body .............................................x1
Soft case ......................................x1
Neckstrap .....................................x1
Lithium battery (CR2) ....................x1
Composition
• Linear distance measurement range: 10-500 meters/11-550 yards/33-999 feet
• Angle measurement range: ±89°
• Distance measurement display step:
[Internal Display]:
(Linear Distance)
0.5 meter/yard, 1 foot
(measurement distance is less than 100 meters/yards/feet)
1.0 meter/yard, 1 foot
(measurement distance is 100 meters/yards/feet or farther)
(Horizontal Distance/Height)
0.2 meter/yard, 0.5 foot
(measurement distance is less than 100 meters/yards/feet)
1.0 meter/yard, 1 foot
(measurement distance is 100 meters/yards/feet or farther)
(Angle)
0.1° (-10°
ー
10°)
1.0° (
≦
-10°, 10°
≦
)
[External Display]:
(Linear distance)
0.5 meter/yard, 1 foot
(Horizontal Distance/Height)
0.2 meter/yard, 0.5 foot
(Angle)
0.1°
• Easy-to-aim 6x optical observation system
• Quantifies the horizontal distance to the target and its height in relation to the
rangefinder's level by measuring linear distance and angle.
• Measure the vertical separation (height between two points).
• The results are displayed on both an internal and an external LCD panel. The
external LCD panel shows all results simultaneously.
• Measure and display in First Target Priority.
• Waterproof design (NOT designed for underwater usage)
• Invisible/Eyesafe IEC Class 1M Laser
• 30-second results display
• Compact, lightweight, ergonomic design
• Automatic shut-off (after approx. 30 sec. unattended)
• Default to “Last Use” settings
• 20-second continuous measuring function
The Nikon Callaway id TECH emits invisible, eyesafe, infrared energy pulses
that reflect off the selected target back to its optical receiver. Sophisticated
precision charge circuitry is used to instantaneously calculate distances, by
measuring the time it takes for each pulse to travel from the rangefinder to the
target and back. Laser reflectivity and measurement results may vary according
to climatic and environmental conditions, the colour, surface finish, size, shape
and other characteristics of the target.
The following factors ensure best range and accuracy:
• Nighttime use
• Cloudy weather
• Bright-coloured targets
• Targets with highly reflective surfaces
• Targets with shiny exteriors
• Large-size targets
• Shooting targets facing at 90 degrees
Measurement may result in inaccuracy or failure in the following cases:
• Slender or small target
• Target has diffusing reflective surface
• Target does not reflect the laser beam (glass, a mirror, etc.)
• Black target
• Target has varing depths
• In snow, rain or fog
• Target measured through glass
• Reflective surface measured from diagonal direction
• Moving target
• Obstacle moving in front of the target
• When targeting the surface of water
Nomenclature
1
Monocular objective lens/
Laser emission aperture
2
Laser detector aperture
3
External LCD
4
MODE button
5
POWER button
6
6x monocular eyepiece
7
Eyecup/diopter adjustment ring
8
Diopter index
9
Strap eyelet
!p
Battery chamber cover
!q
Battery chamber cover “Open/
Close” indication
!w
Product number/explanatory label
!e
Laser warning label
Internal Display
1.
『
』
- Target focusing/Laser irradiate system
『
』
- Aim at the target. Position the target
at the center of the reticle.
『
』
- Appears while the laser is being used
for a measurement. (Remains present during
single measurement.Blinks during continuous
measurements.)
Warning: Do not look into the objective lenses
when this mark is shown.
2
．
『
』
: Distance/measurement status display
Digitally indicates measured distance in meters/yards/feet and angles in
degrees. Also indicates measuring status such as “Measurement in
progress”, “Measurement unsuccessful” or “Unable to measure.”
<Examples of measurement results>
(Distance)
Display of results: (
≧
100m/yards/feet) e.g. 234 meters =
『
』
Display of results: (
＜
100m/yards)
e.g. 76.5 yards =
『
』
Display of results: (
＜
100 feet)
e.g. 82 feet =
『
』
(Angle)
Display of results: (
≦
-10
˚
and
≧
10
˚
) e.g. 36˚=
『
』
e.g. -29˚=
『
』
Display of results: (-10
˚
＜
and
＜
10
˚
)
e.g. 3.5˚=
『
』
e.g. -7.0
˚
=
『
』
『 』
- Now measuring
『
』
- Failure to measure or unable to measure distance
3.
『
』
Display Units
『
』
Indicates distance being measured in meters.
『
』
Indicates distance being measured in yards.
[No unit displayed]
Indicates distance is measured in feet.
4.
『
』
- Indicates battery condition. (See
"
Changing Batteries
"
)
5.
『
』
Display Modes
(See “Measurement and Display” for operations and display examples.)
Linear distance mode
『
』
Calculates linear distance to your target and displays the results.
Horizontal distance mode
『
』
Calculates horizontal distance to your target by measuring
the linear distance and angle, and displays the results.
Height mode
『
』
Measures your target's height from the horizontal level, and
displays the results.
Vertical separation (height between two points) mode
『
』
Uses the linear distance and angle data of two points to
calculate and display the vertical separation (height
between the two points.)
Angle mode
『
』
Measures the angle of your target from the horizontal level
and displays the results.
Although the LCD was produced using the most advanced technology, it is
impossible to eliminate dust completely. When using this product, the LCD is
magnified by high magnification of the eyepiece lens and dust may appear as
a defect. It will not, however, affect measurement accuracy.
Operational Summary
Caution—use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure
1. Install a battery in the battery chamber. (See Changing
Batteries)
2. Rubber eyepiece cup
Eyeglass wearer: Collapse the eyepiece cups.
Non-eyeglass wearer: Do not collapse the eyepiece cups.
3. Diopter adjustment
Adjust diopter to obtain a clear image in the LCD.
First, rotate the diopter adjustment ring counterclockwise until it comes to a
complete stop. Next, turn on the power to activate the LCD when you look
through the Nikon Callaway id TECH. Rotate the diopter adjustment ring
clockwise until the display comes into focus.
If the diopter is not adjusted to correspond to your eyesight, you may not be
able to clearly focus your subject.
4. Measuring
Note: See separate “Measurement and Display” sheet for external LCD panel.
Note: Depressing and holding down the POWER button causes all symbols to be
displayed in the internal LCD panel. After you remove your finger from the
POWER button, the last-used setting is displayed. (If you briefly press the
POWER button then remove your finger, the LCD panel may display the last-
used setting without displaying all of the symbols. This is not a malfunction
or other problem.)
Before measuring, be sure to confirm settings, such as unit, measurement/display
mode and priority mode.
◎
: See the relevant mode section in this manual for setting.
Changing Batteries
Type of battery:
3V CR2 lithium battery
Battery condition indicators
:
Battery has enough charge for use.
:
Battery charge is getting low.
flashing: Battery charge is low and battery
should be replaced.
disappears: Battery is exhausted and should
be replaced.
flashing in the LCD indicates that the battery should be replaced.
1
Open the battery chamber cover
Using the ball of the thumb or a coin in the recessed part of the battery
chamber cover, rotate the cover following the Open/Close arrow indicator. It
may not open easily due to its rubber packing for water resistance.
2
Replace the old battery with a new one
Install new battery with the [+] and [-] correctly positioned following the
“Battery installation” indication seal in the battery chamber. (Insert battery
positioning the [+] pole towards the inside of the chamber.) [The Nikon
Callaway id TECH will not operate if the battery is installed incorrectly.]
3
Close the battery chamber cover
Align the Open/Close indicator with the white dot and insert the battery
chamber cover. Using the ball of the thumb or a coin, turn the cover in the
opposite direction to the arrow indicator. It may not close easily due to the
rubber packing for water resistance, but continue to turn it all the way until
it stops. Confirm that the cover is securely closed.
Battery life
Continuous operation:
Approx. 10,000 times (at 20°C)
Target focusing, measurement, and automatic power off are included in a
single cycle. This figure may differ according to temperature, and other
factors such as target shape, colour, etc.
* The Nikon Callaway id TECH come with a 3V CR2 lithium battery. However, due to
natural electric discharge, the life of the battery will likely be shorter than that noted
above.
Replace battery if the Nikon Callaway id TECH is ever submerged in water or if water
enters in the battery chamber.
Specifications
Laser Rangefinder
Thank you for purchasing the Nikon Callaway id TECH.
This high-spec laser rangefinder features a new angle measurement function in
addition to the existing linear distance measurement function for enhanced
enjoyment of sports and other outdoor applications. (The Nikon Callaway id
TECH is also able to measure the horizontal distance to a target and its height.)
Please observe the following guidelines strictly so you can use the equipment
properly and avoid potentially hazardous problems. Before using this product,
read thoroughly the “SAFETY PRECAUTIONS” and instructions on correct usage
accompanying the product.
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Keep this manual within reach for easy reference.
• Specifications and design are subject to change without notice.
• No reproduction in any form of this manual, in whole or in part (except for brief
quotation in critical articles or reviews), may be made without written
authorization from NIKON VISION CO., LTD.
Instruction Manual
Callaway id TECH
POWER
Set FULL/Limited
measurement mode
LCD is illuminated
Set your desired modes
◎
Align the reticle
with the target
POWER
appears
Results are converted to the
mode set and displayed.
MODE
Indication
remains
illuminated for
30 sec.
30 seconds pass without operation
＊
Power off: LCD indications disappear
Measure a
gain
Fail to measure
Cannot measure
Successfully
measured
For continuous distance
and angle measurement
(up to 20 seconds), keep
button depressed.
※
or
☆
☆【
Continuous measurement mode
】
Keeping the POWER button depressed allows you to perform
continuous measurement for 20 seconds.
Blinks while performing measurements.
When measuring a pin at a golf course, for example, use Continuous
measurement mode for easy measurement. With no objects between you
and the pin, the smallest number is the distance to your targeted pin.
※
See the “Measurement and Display” sheet for details regarding the
operations and results display of the various modes.“
＊
Power turns off 30 seconds after the last operation.
5. Selecting display unit
(Factory default setting is yard.)
Meter [
]
Yard [
]
Feet [ ]
1. Confirm the LCD panel is on.
2. Press and hold the
button for approx. two seconds.
3. When display unit has switched, release the
button.
4. Repeat steps 2 and 3 until your desired mode is displayed.
5. When you have completed setting, results will be converted and displayed
in the your selected measurement unit.
6. Switching measurement/display modes
(Factory default setting is
linear distance measurement mode)
Linear Distance [
]
Horizontal Distance [
]
Angle [
]
Height [
]
Vertical Separation
between 2 points point
[
]
By pressing the MODE button, modes will change in
the order indicated above.
The angles and heights of two points are displayed
only at the full-mode setting.
1. Confirm the LCD panel is on.
2. Press
button within 0.5 seconds.
3. Release
button to switch the mode.
4. Repeat steps 2 and 3 until your desire mode is displayed.
5. Switching the mode after measurement converts the results to the new
mode.
6. After the mode is set, measurements are performed in the new mode.
7. Switching Full/Limited modes
(default setting is limited mode)
1. Confirm the power is off (LCD is off).
2. Press and hold
button, then depress and hold
button
within 0.5 second.
3. Continue to press and hold both buttons, (more than 2 seconds),to
confirm the internal display is on.
When these buttons are pressed, all symbols are displayed . When
『
』
and
『
』
symbols do not appear, Limited mode is
switched to Full mode.
Note
）
If buttons are not pressed in the correct order, switching will
not take place.
Note
）
This mode change can also be confirmed when switching the
measurement/display mode.
4. Release buttons.
8. Distance display
Nikon Callaway id TECH is First Target Priority Distance Display System.
When obtaining different results from a single measuring operation. The Nikon
Callaway id TECH will display the distance to the nearest target on the LCD
panel.
ex.) When measuring a tree standing in front of a house;
"115m" (distance to the tree) will be displayed. This mode has application for
golf.
9. Low battery indication
Flashing
indicates that the battery charge is low and battery should
be replaced. (See "Changing Battery")
Optical system
Type
Roof-prism monocular
Magnification
6x
Effective diameter of objective lens (mm)
ø21mm
Angular field of view (real)
6.0°
Eye relief (mm)
18mm
Exit pupil (mm)
ø3.5mm
Dioptre adjustment
±4m
-1
Others
Operating temperature
-10° — +50°
Power source
CR2 lithium battery x 1, 3V DC,
Auto Power Off (approx. 30 seconds)
Dimensions (D x W x H)
130 x 45 x 69 mm
Weight
Approx. 210g (without battery)
Structure
Body: Waterproof (maximum depth of 1 meter
for up to 10 minutes)*
（
Battery chamber: Water resistant**
）
Safety & EMC
Class 1M Laser product (IEC68025-
1:2001)
FCC Part15 subpart B Class B
CE, EMC directive, c-tick, WEEE
* Waterproof models
The Nikon Callaway id TECH is waterproof, and will suffer no damage to the
optical system if submerged or dropped in water to a maximum depth of 1 meter
for up to 10 minutes.
The Nikon Callaway id TECH offers the following advantages:
• Can be used in conditions of high humidity, dust and rain without risk of
damage.
• Nitrogen-filled design makes it resistant to condensation and mold.
Observe the following when using the Nikon Callaway id TECH.
• As the unit does not have a perfectly sealed structure, it should not be
operated nor held in running water.
• Any moisture should be wiped off before adjusting movable parts (eyepiece,
etc.) of the Nikon Callaway id TECH to prevent damage and for safety reasons.
To keep your Nikon Callaway id TECH in excellent condition, Nikon Vision
recommends regular servicing by an authorized dealer.
** The battery chamber is water resistant, not waterproof. Water may enter the
device if the Nikon Callaway id TECH is submerged in water. If water enters
the battery chamber, wipe out any moisture and allow time for the chamber to
dry.
Troubleshooting/Repair
If problems persist after consulting the Troubleshooting Table,
please contact your local dealer to check/repair the Nikon
Callaway id TECH. Never let anyone than the official
representative of the product manufacturer check or repair the
Nikon Callaway id TECH. Failure to follow this instruction could
result in injury, or damage to the product.
Symptom
Check Points
Unit does not turn on —
LCD fails to illuminate
Target range cannot be
obtained
[- - -] (“Cannot
measure”) appears
Closer target cannot be
measured
Target beyond a certain
distance cannot be
measured
Measurement result is
unstable
Incorrect result is
displayed
• Depress POWER button.
• Check and replace batteries if necessary.
• Be sure that nothing, such as your hand or finger, is
blocking the laser emission aperture and laser
detector.
• Be sure that the laser emission aperture and laser
detector are clean. Clean them if necessary.
• Be sure that the target shape and condition is
appropriate to reflect the laser beam.
• Replace battery.
• Be sure to hold the unit steady while depressing the
POWER button.
• Be sure the target is within measuring range (10 -
500m/11 - 550 yards/33-999 feet)
• Be sure that nothing, such as leaves or grass, is
between the Nikon Callaway id TECH and the target.
• Be sure that nothing, such as leaves or grass, is
between the Nikon Callaway id TECH and the target.
• Replace battery.
• Be sure that the target shape and condition is
appropriate to reflect the laser beam.
• Be sure to hold the unit steady while depressing the
POWER button.
• Be sure that nothing, such as leaves or grass, is
between the Nikon Callaway id TECH and the target.
• Replace battery.
• Be sure that the target shape and condition is
appropriate to reflect the laser beam.
• Be sure that nothing, such as leaves or grass, is
between the Nikon Callaway id TECH and the target.
If your Nikon Callaway id TECH should require repair, please contact your local
dealer for details regarding where to send it. Before doing so, you are advised to
consult the Troubleshooting Table below.
Do not use the Nikon Callaway id TECH for purposes beyond the limits of its
stated accuracy.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules and to EU EMC
directive. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two condition0s:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
E
Tree
Fence
House
Distance to Target
115m
123m
128m
Measurement System
Measurement mode
Linear distance
: Act
display
Horizontal distance
: Hor
Height
: Hgt
Angle
: Ang
Vertical separation (height between two points ): Hgt + Hgt2
Measured distance/ Distance: 10-500 meters/11-550 yards/33-999 feet
angle range
(999 feet: 304.5 meters/333 yards)
Angle:
±89°
Distance-
Act
0.5 meter/yard, 1.0 foot (
＜
100 meters/yards/feet)
Angle
(Linear distance)
1.0 meter/yard, 1.0 foot (
≧
100 meters/yards/feet)
Display
Hor
0.2 meter/yard, 0.5 foot (
＜
100 meters/yards/feet)
Steps
(Horizontal dist.)
1.0 meter/yard, 1.0 foot (
≧
100 meters/yards/feet)
Hgt
0.2 meter/yard, 0.5 foot (
＜
100 meters/yards/feet)
(Height)
1.0 meter/yard, 1.0 foot (
≧
100 meters/yards/feet)
Ang (Angle)
0.1° (
＜
10°), 1.0°(
≧
10°)
Linear distance 0.5 meter/yard, 1.0 foot
Horizontal dist. 0.2 meter/yard, 0.5 foot
Height
0.2 meter/yard, 0.5 foot
Angle
0.1°
System
First Target Priority Distance Display system
Internal
External
Laser
Class
IEC Class 1M
Wavelength
870 nm
Pulse duration
14 ns
Output
15W
Beam divergence
Vertical
：
5° — 8°, Horizontal
：
25° — 36°
Operating humidity
80% RH (without dew condensation)
Laser Rangefinder
8
6
1
3
7
4
2
!e
!w
!q
9
!p
5
