9(26)
Servodan A/S | Tel +45 7442 4726 | Fax + 45 7442 4035 | [email protected] | www.servodan.com
The light
must
be switched on via the operating button and is
daylight-independent. ECO Off and long press deactivated.
Automatic off via detector after end of cut-off time (Auto Off) or
light level. Light sensor has first priority.
The light switches off automatically after a predetermined period
when registration of activity in the detector’s coverage area has
ceased, or the light level remains above the preset level for five
minutes.
230 V operating button must be connected.
Setting the light level and cut-off time is performed via the
integrated potentiometers or via the IR remote control 41-926
(accessory).
Example 3:
E.g. staircases
DIP switch settings:
1
2
3
4
On
x
x
x
Off
Automatic on/off via daylight-dependent sensor. Light sensor has
first priority.
The light switches on automatically when the detector detects
activity within the coverage range and the light level is below the
preset level.
The light switches off automatically after a predetermined period
when registration of activity in the detector’s coverage area has
ceased, or the light level remains above the preset level for five
minutes.
The light can
always
be switched on via the operating button,
regardless of the daylight level.
230 V operating button must be connected.
Setting the light level and cut-off time is performed via the
integrated potentiometers or via the IR remote control 41-926
(accessory).
Operation & maintenance
Dirt affects the operation of the detector and the detector’s lens
must therefore be kept clean. Use a damp cloth for cleaning. Use
water mixed with ordinary detergent. Avoid putting pressure on
the lens. If the lens or other parts of the detector are defective, it/
they must be replaced.
Technical data
Input:
Power supply ............................................ 230 V AC 50 Hz ±10%
Power consumption .................................. 0.2 W
Output:
Relay potential free .................................... NO, 230 V, µ 10 A
Load:
Incandescent lamps ............................. 2,300 W
Fluorescent tubes, uncompensated .... 1,200 VA
Halogen incandescent lamps .............. 2,300 W
Max. compensation capacity .................... 140 µF
Max. starting peak ..................................... 165 A/20 m sec.
Performance:
Lux range (preset settings) ........................ 20–1,000 lux
Time range (preset settings) ...................... Pulse, 2–60 min.
Range ........................................................ Ø16-32 m, 360°
Installation height ...................................... 4-8 m
Sensitivity ................................................. 4 settings
Enclosure class ......................................... IP 54
Cable dimension (Ø14 mm max.) .............. 3 pcs. 5 x 2.5 mm
²
Ambient temperature ................................. -5°C to +50°C
Certification:
CE in accordance with .............................. EN 60669-2-1
Accessories
IR Remote .................................................. 41-926
Motion detector, slave ............................... 41-773
Remote control
Settings using IR remote control:
Fig. 8.
Lock/unlock:
Press three times to “unlock the sensor” – edit mode. Each press
is indicated with a flash from the green LED.
The detector acknowledges with two flashes from the green LED.
Press Lock/Unlock 3 times within 5 seconds.
Press once to “lock the sensor” – operating mode. The detector
acknowledges with two flashes from the green LED.
For all settings (except Light On/Off, Short push, Long push,
Status Ch 1, Status Ch 2 and LED On/Off) the detector must be
unlocked, the setting selected and then the detector must be
locked again for the setting to become active.
If the detector is not locked, it will lock automatically after two
minutes and any modified settings will be saved.
Light On/Off (1 & 2):
This function turns the light on/off constantly, regardless of
registered activity or light levels. If this function is activated, the
red LED will flash On for 0.25 secs and Off for 10 secs.
The detector will remain in this function until it is discontinued
either by pressing three times on ”Light On/Off” within five
seconds or one time on the button ”Short push”.
The detector will then return to automatic operation settings.
LED On/Off:
When the functions ”Long push” and ”Light On/Off” are
activated, this is indicated via LED. To turn this indicator off, use
”LED On/Off”.
Ch 1 and Ch 2 buttons:
To set the Lux and Time settings for channel 1, CH 1 must first
be pressed.
GB
