(OLD CAL V
(OLD CAL V
(OLD CAL V
(OLD CAL V
(OLD CAL VAL
AL
AL
AL
ALUE)(TRUE DIST
UE)(TRUE DIST
UE)(TRUE DIST
UE)(TRUE DIST
UE)(TRUE DISTANCE) = NEW CAL V
ANCE) = NEW CAL V
ANCE) = NEW CAL V
ANCE) = NEW CAL V
ANCE) = NEW CAL VAL
AL
AL
AL
ALUE
UE
UE
UE
UE
DISPLA
DISPLA
DISPLA
DISPLA
DISPLAYED DIST
YED DIST
YED DIST
YED DIST
YED DISTANCE
ANCE
ANCE
ANCE
ANCE
1 8
1 8
1 8
1 8
1 8
CALIBRATION
The SpeedCoach is factory calibrated to provide accurate performance in
most shells with the impeller installed 16’3” (5 m) from the bow. Calibration
is an optional step which allows the display unit to compensate for different
impeller locations, and to perform accurately to your boat. You do not need
to calibrate your system if you are concerned only with comparing
performance from day to day. To calibrate your system, row or paddle over
a measured distance on still water (on flowing water, row or paddle both up
and down stream and average the results shown on your display). Then, use
the following formula to obtain your new calibration value:
For example, if you know you covered 1 mile, but your display shows 0.92,
your calibration value will be:
PLEASE NOTE: Calibration is boat and impeller location-specific: if you move
your unit to a new boat, or modify the location of your impeller, it is
recommended that you recalibrate the unit.
(1.00)(1.00) = 1.086
(1.00)(1.00) = 1.086
(1.00)(1.00) = 1.086
(1.00)(1.00) = 1.086
(1.00)(1.00) = 1.086
0.92
0.92
0.92
0.92
0.92
1 9
1 9
1 9
1 9
1 9
CALIBRATION (cont.)
To change the calibration number, hold the bottom button in for 3 Seconds
until you see “CAL” in the lower left screen (a), then release. Now you will
see the number with the first digit flashing (b).
a
b
Press the bottom button to change this
number.
Hold bottom button for 1 second to move
between digits (c).
Repeat hold and press to move through
and change all appropriate digits (d).
Hold to exit.
d
c
1 7
1 7
1 7
1 7
1 7
RESETTING YOUR TIMER
To reset the timer, hold the top button
down for 3 Seconds then release when
you see “rESEt ” in the lower left
window (a). The “push button indicator”
now appears in the upper right window
(b). Press the lower button to clear the
memory (c). The unit will automatically
return to the ready screen.
c
b
a
If the display seems faint (a) then the
battery is probably low.
To replace the battery, open the battery
door with a flat head screw driver (b)
(a coin will also work).
Remove battery door and replace the 3V
Lithium CR2032 battery with new one
(c) and replace door.
To zero out the distance log, hold the
top button down for 10 seconds with the
battery out. Then replace battery.*
*If you have calibrated your unit, you
*If you have calibrated your unit, you
*If you have calibrated your unit, you
*If you have calibrated your unit, you
*If you have calibrated your unit, you
will need to re-enter your adjusted
will need to re-enter your adjusted
will need to re-enter your adjusted
will need to re-enter your adjusted
will need to re-enter your adjusted
calibration factor after removing the
calibration factor after removing the
calibration factor after removing the
calibration factor after removing the
calibration factor after removing the
battery
battery
battery
battery
battery.....
REPLACING THE BATTERY
a
b
c
2 0
2 0
2 0
2 0
2 0
