background image

24

 –

 

English

10

WHAT TO DO IF...

In case of malfunction due to problems during installation of failure of parts, refer to table 13: 

Table 14

Problem

Solution

The radio transmitter does not control the 

gate and the led on the transmitter does not 

light up

Check to see if the transmitter batteries are exhausted, if necessary replace them

The radio transmitter does not control the 

gate but the led on the transmitter lights up

Check to see if the transmitter has been memorised correctly in the radio receiver.
Check that the emission of the transmitter radio signal is correct by means of this empirical test: 

push a key and rest the LED on the aerial of a normal radio (ideally an economical one) that 

is switched on and tuned in, as close as possible, to 108.5Mhz FM; a slight crackling sound 

should be heard

No  manoeuvre  starts  and  the  OK  LED  fails 

to flash.

Check that the product is being supplied 230 V mains power 

Check to see if fuses F1 and F2 (fig. 7) have blown; if necessary, identify the reason for the 

failure and then replace the fuses with others that have the same current rating and specs

No manoeuvre starts and the flasher is off

Check that the command is actually received: if the command reaches the Step-by-Step input, 

the OK led flashes twice to indicate that the command has been received

11

DISPOSAL OF THE PRODUCT

This product constitutes an integral part of the automation system, therefore it must be disposed of together with the former.

As in installation, also at the end of product lifetime, the disassembly and scrapping operations must be performed by qualified personnel.

This product is made up of different types of material, some of which can be recycled while others must be disposed of. Seek information on the 

recycling and disposal systems envisaged by the local regulations in your area for this product category.

 CAUTION! – Some parts of the product may contain polluting or hazardous substances which, if disposed of into the environment, 

constitute serious environmental and health risks.

As indicated by the symbol, the product must not be disposed of as domestic waste. Sort the materials for disposal, according 

to the methods envisaged by current legislation in your area, or return the product to the retailer when purchasing an equivalent 

product.

 CAUTION! - Local legislation may include the application of serious fines in the event of improper disposal of this 

product.

Summary of Contents for ROBO600

































Reviews: