12
– English
Remote memorising
It is possible to enter a new transmitter in the receiver memory without using
the keypad. A previously memorised and operational remote control must be
available. The new transmitter will “inherit” the characteristics of the previously
memorised one. Therefore, if the first transmitter is memorised in mode I, the
new one will also be memorised in mode I and any of the buttons of the trans-
mitter can be pressed. If the first transmitter is memorised in mode II the new
one will also be memorised in mode II but the button activating the required
output must be pressed on the first transmitter as must the button required to
be memorised on the second. You need to read all the instructions in advance
so you can perform the operations in sequence without interruptions. Now,
with the two remote controls (the NEW one requiring code memorisation and
the OLD one that is already memorised), position yourself within the operating
range of the radio controls (within maximum range) and carry out the instruc-
tions listed in the table.
All the memorised codes can be deleted as follows:
DELETING ALL TRANSMITTERS
4
TECHNICAL CHARACTERISTICS OF THE PRODUCT
Receivers:
SMXI
SMXIS
Decoding
Rolling code 52 bit FLOR
Rolling code 64 bit SMILO
Transmitter compatibility
FLOR, VERY VR, NICE WAY, ERGO, PLANO, NICE ONE
SMILO
Frequency
433.92 MHz
433.92 MHz
Input impedance
52 KΩ
52 KΩ
Outputs
4 (on SM connector)
4 (on SM connector)
Sensitivity
better than 0.5 µV
better than 0.5 µV
Working temp.
from -10°C to + 55° C
from -10°C to + 55° C
Transmitters:
FLO2R
SMILO
Buttons
1, 2 or 4 according to the versions
2 or 4
Power input
12 V Batt. 23 A
12 V Batt. 23 A
Absorption
10 mA
25 mA
Transmission frequency
433.92 MHz
433.92 MHz
Working temp.
from -10°C to + 55° C
from -10°C to + 55° C
Radiated power
estimated approximately 1 mW E.R.P.
estimated approximately 1 mW E.R.P.
Range
estimated 200 m (outdoors); 35 m (indoors)
estimated 200 m (outdoors); 35 m (indoors)
Dimensions / Weight
69 x 39 x 15,5 mm / 31 g.
Ø 48 mm x H 14 mm - 14 g
Encoding
digital (4.5 x10
15
combinations)
digital (18 x 10
15
combinations)
WARNINGS:
• All technical characteristics stated refer to an ambient temperature of 20°C (±5°C). • Nice S.p.a reserves the right to modify the product at any
timee, while maintaining the same functionalities and intended use. • The range of the transmitters and the reception capacity of the receivers may be subject to
interference that may alter their performance. In the event of interference, Nice cannot guarantee the effective capacity of their devices.
TABLE B3 - Remote Memorising
01.
Press the button on the NEW transmitter for at least 5 seconds and then release
02.
Press the button on the OLD transmitter 3 times slowly
03.
Press the button on the NEW transmitter slowly and then release
Note
– If there are other transmitters to memorise, repeat the above steps for each new transmitter .
1s
x1
TX
TX
TX
TX
TX
TX
1s
1s
x5s
TABLE B4 - Deleting all transmitters
01.
Press the receiver button and hold it down
02.
Wait for the Led to light up, then wait for it to switch off and then wait for it to flash 3 times
03.
Release the button exactly during the third flash
Note
– if the procedure was performed correctly, the Led will flash 5 times after a few moments.
RX
RX
x3
3°
x5
EN
www.metalines.com
