10
– English
WARNINGS:
• All technical characteristics stated refer to an ambient temperature of 20°C (±5°C). • Nice S.p.a reserves the right to modify the product at any
timee, while maintaining the same functionalities and intended use.
Mains power supply
MC424 Control units:
230 V
~
±10% 50 ÷ 60 Hz
MC424/V1 Control units: 120 V
~
±10% 50 ÷ 60 Hz
Max absorbed power
170 W
Emergency power supply
for PS124 buffer batteries
and for Solemyo solar kit
Maximum motor current:
3A (with a “level 6” current sensitivity cut in)
Service power output
24 V 200 mA maximum current (the voltage can vary from 16 to 33 V )
Phototest Output
24 V 100 mA maximum current (the voltage can vary from 16 to 33 V )
Flashing lamp output
for flashing lamp 24 V , maximum power 25 W (the voltage can vary from 16 to 33 V )
Gate open indicator output
for indicator lamps at 24 V maximum power 5 W (the voltage can vary from 16 to 33V )
or electric locks
12 V
~
25 W
STOP Input
for NC contacts or constant resistance 8,2 KΩ +/- 25%
Working time
automatic detection
Pause time
programmable at 5, 10, 20, 40, 80 seconds
Discharge time
programmable to 0, 0.3, 0.7, 1.3, 2 seconds
Leaf delay in open cycle
programmable at 5, 10, 20, 30 and 40 % of working time
Leaf delay in close cycle
automatic detection
1st motor output
for Wingo WG4024 - WG5024
2nd motor output
for Wingo WG4024 - WG5024
Max. cable length
power supply
30 m
Solemyo solar power kit
3 m
motors
10 m
other inputs/outputs
30 m
flashing light
10 m
SCA
30 m
electric lock
10 m
aerial
20 m
(
recommended less than 3 m
)
Radio receiver
“SM” type coupling for receivers SMXI, SMXIS, OXI (Mode I and Mode II)
Temperatura di esercizio
from - 20 to 50 °C
Protection rating
IP 54 with enclosure intact
Dimensions (mm)
310 x 232 x H 122
Weight (kg)
4,1
TECHNICAL CHARACTERISTICS OF THE PRODUCT
EN
CE declaration of conformity
Declaration in accordance with the following Directives: 2004/108/EC (EMC); 2006/42/EC (MD) annex II, part B
Note - The content of this declaration corresponds to that specified in the official document deposited at the Nice S.p.A. headquarters and, in particular, to the latest revised edition
available prior to the publishing of this manual . The text herein has been re-edited for editorial purposes . A copy of the original declaration can be requested from Nice S .p .A . (TV) I
.
Number:
296/MC424
Revision:
3
Language:
EN
Manufacturer’s Name:
Nice s.p.a.
Address:
Via Pezza Alta 13, Z.I. Rustignè, 31046 Oderzo (TV) Italy
Person authorised to compile
the technical documentation:
Nice s.p.a.
Type of product:
Two 24 Vdc motor control unit
Model / Type:
MC424
Accessories:
SMXI, SMXIS radio receiver
The undersigned Mauro Sordini, as Chief Executive Officer, hereby declares under his own responsibility that the product identified above complies with the
provisions of the following directives:
• DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 15 December 2004 on the approximation of the laws of Member Sta-
tes relating to electromagnetic compatibility and repealing Directive 89/336/EEC, in accordance with the following harmonised standards:
EN 61000-6-2:2005, EN 61000-6-3:2007+A1:2011
In addition, the product conforms to the following directive in accordance with the provisions applicable to partly completed machinery:
Directive 2006/42/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of May 17 2006 regarding machines and amending directive 95/16/EC (consoli-
dated text)
• I hereby declare that the pertinent technical documentation has been drafted in accordance with Annex VII B of Directive 2006/42/EC and that the following essential requirements
have been fulfilled: 1.1- 1.1.2- 1.1.3- 1.2.1-1.2.6- 1.5.1-1.5.2- 1.5.5- 1.5.6- 1.5.7- 1.5.8- 1.5.10- 1.5.11
• The manufacturer agrees to send the national authorities any pertinent information on partly-completed machinery, in response to a motivated request, without affecting its intel-
lectual property rights.
• If the partly completed machinery is operated in a European country with an official language other than the language used in this declaration, the importer must include a tran-
slation with this declaration.
• The partly completed machinery must not be operated until the final machine in which it is to be incorporated is declared to conform to the provisions of Directive 2006/42/EC,
if applicable.
The product also complies with the following standards:
EN 60335-1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:2011, EN 60335-2-103:2003+A11:2009
All parts of the product subject to the following standards comply with them:
EN 13241-1:2003+A1:2011, EN 12445:2002, EN 12453:2002, EN 12978:2003+A1:2009
Oderzo, 30 July 2014
Mr. Mauro Sordini (Chief Executive Officer)
www.metalines.com
