Nice E Star LT, Instructions For Installation And Use Manual

Page: 8 / 24

6 – English
EN
5.6 - Tensioning the fabric: “FRT” function (position “2”)
This function is used to tension the awning canvas when open. The function is activated by programming position “ 2 ” in Era Star T.
During use of the automation, when the awning opens, the motor moves it first to position “ 1 ” and then immediately tensions the canvas by automatically activating a
short up movement to position “ 2 ”.
Caution! - The “FRT” function level can only be set after programming the limit position values “0” and “1”.
• To activate the “FRT” function
01. Use the Up or Down button to move the awning to the point of mid-travel.
02. Use the Down button to move the awning to position “ 1 ”.
03. Press and hold both the Up and Down buttons until the awning performs a short up movement and then release the buttons.
04. Use the Up button to close the awning by a few centimetres, until the canvas can be seen to be adequately tensioned (this will be position “ 2 ”).
05. Press and hold both the Up and Down buttons until the awning performs a short up movement and then release the buttons.
04
THE
END
02 01
“ 2 ”(
1 )
03
5
sec.
5
sec.
05
( 1 )
“ 2 ”
2/3c
m~
1
1
“ 1 ”
• To deactivate the “FRT” function
01. Use the Up or Down button to move the awning to the point of mid-travel.
02. Press and hold both the Up and Down buttons until the awning performs a short up movement and then release the buttons.
03. Press and hold the Down button to move the awning to limit position “1” and release at exactly the time at which the awning stops at this limit.
04. Press and hold both the Up and Down buttons until the awning performs a short up movement and then release the buttons.
Note – After cancelling position “2” the awning will move between the limit positions “0” and “1”.
03
5
sec.
02 01
04
5
sec.
THE
END
1
1
“ 1 ”
English – 6
5.7 - Awning with AUTOMATIC hook-up of fabric on opening: “FTC” function
This function enables automatic connection and disconnection of the awning. The “FTC” function can only be activated if the automatic fabric connect/disconnect
mechanism is present on the awning, in a single position , located in alignment with the awning opening position. The motor enables memorisation of only one hook-
up position.
In general this type of mechanism has a stop for mechanical connection of the awning and two additional points (positioned beyond the stop) which the awning must
reach to enable connection (in position “ 1 ”) and disconnection (in position “ S ”) of the canvas.
Therefore to ensure correct operation of this mechanism, the two positions “1” and “S” must be set and memorised as described below.
Caution!
• Before programming the “FTC” function, ensure that limit positions “0” and “1” have not been memorised; if necessary, cancel them according to
procedure 5.9. • Position “1” must be located a few centimetres be yond the mechanical connection stop. During opening. this will enable the canvas
to reach first position “1” and then hook up to the mechanical stop during ascent. • Position “S” must be located a few centimetres be yond the discon-
nection mechanism. During closure, this will enable the canvas to reach first position “S”, automatically detach from the mechanical stop and then raise
to the closing limit position “0”.
• (The “RDC” function remains enabled)
01. Use the Up or Down button to move the awning to the point of mid-travel.
02. Press and hold Up until the awning stops automatically at limit switch “ 0 ”; then release the button.
03. Press and hold Down and move the awning beyond the hook-up point, stopping it a few centimetres further than this point (if necessary correct the position using
the two buttons).
“ 1 ”
( )
S
6 – English
EN
THE
END
THE
END