background image

 

APPLICATIONS

 

The 

Apollo 

Model 155

0

ETL-1K/165

0

ETL-1K Swing Gate Operator is approved for 

Vehicular Class I & II 

us-

age under 

UL 325 

Guidelines, and is designed to handle swing gates up to 16 feet in length and 6

00 

pounds 

each. A professional fence or gate dealer is recommended to assure proper installation. 

Apollo Gate 

Operators

 are available only through qualified dealers with an outstanding reputation in the fence and gate 

industry. These dealers will be able to recommend the proper equipment for particular applications. 

Apollo 

Gate Operators 

are 12 Volt DC (

Direct Current

) powered. A 12 Volt sealed battery  (33 ampere hour minimum) 

with connecting posts located on the top is recommended. There are several advantages with 12 Volt DC 
systems: 

 

 

Low voltage virtually eliminates risk of electrical shock.

 

 

Battery powered operators provide up to 200 operations in the event of power outages.

 

 

The battery may be recharged with a trickle charger or by solar energy  (Electrical battery chargers 
should have a class 2 transformer rating). 

 

 
With Battery connected to trickle charger (use Part# 404 from page 6) 

If a trickle charger is used and a standard electrical outlet is not readily available, a licensed electrician will be 
required for proper electrical hook up.

 

The following table should be used as a guide for capacity of operation of operators only, additional options 
may reduce the the daily usage. 

Please note that the charge capability of solar panels will vary with different 

geographical locations, please reefer to Table 1 below. 
 

1050 Gate Operator Solar Charge Controller  (With Solar Panel) 

The built-in solar charge controller provides maintenance-free protection for 12VDC batteries and solar panels 
by preventing overcharging.  Charging current is adjustable from 0.10 Amps to 1.50 Amps in 0.05 Amp incre-
ments, with adjustable cycle times and Auto Off/On.  The battery charge profile may be manually adjusted to 
match a particular battery’s specifications, or default settings can be used to maintain the majority of 12VDC 
batteries on the market. The charging algorithm is temperature compensated using a built-in temp sensor to 
further protect batteries against overheating and overcharging.

 

                              Daily Cycles       

1-10  1-20  1-40  1-60 

1-80 

80+ 

5 watt solar panel 

 

 

 

 

 

10 watt solar panel 

 

 

 

 

 

20 watt solar panel 

 

 

 

 

 

 

40 watt solar panel 

 

 

 

 

 

 

1.5 amp battery charger 

 

 

 

 

 

10 amp battery charger 

 

 

 

 

 

Note: Double the amount of solar panels for Dual Gate Operators.

 

Charging Methods for Average Daily Usage

 

Specifications 

Charging Current: 

.10 – 1.50A in .05A increments 

Cycling On/Off:  

4s – 30s in 1s increments 

Auto:                        

Off/On 

Table 1 

III 

Summary of Contents for 1550ETL-1K

































Reviews: