background image

 

29 

TABLE 3 

SYMPTOM(S) 

POSSIBLE SOLUTION 

Operator will not power 
On. 
Power LED is OFF 

 

Check terminal Lock wiring for loose or broken wires 

 

Check the fuse 

 

Check wiring polarity 

Gate opens a short dis-
tance, then stops and 
reverses 

 

Check the UL/Edge input on the gate controller 

 

Adjust Force Settings 

 

Check Motor 1 and Motor 2 encoder LEDs to verify the LEDs toggle when 
the gate is moving 

Gate opens but will not 
close 
 

 

Check the input LEDs. Any ON will hold the gate open and indicates a 
problem with a keying device 

 

Check the secondary safety devices. Any activated safety devices will 
hold the gate open and indicates a problem with the safety device 

 

Check the loop detectors. Any activated safety devices can hold the gate 
open and indicates a problem with the loop detector or ground loop 

Hard Shutdown (2 back 
to back obstructions) 
LED  blinking, Buzzer 
sounds for 5 minutes 

 

Clear any obstructions from the path of the gate. Press RESET to clear (or 
hard reset button) 

Gate opens by itself 

 

Check accessory inputs and clear them as necessary 

15 - APOLLO GATE OPENER TROUBLESHOOTING 

TABLE 2  

COMPLETE  BASIC 

 

Alarm 

Active the primary (inherent) reverse system by blocking the gate 
with a solid object. The gate should reverse momentarily then stop. 
Restart the gate and Lock again with a solid object. The gate should 
reverse momentarily, then stop, and go into hard shutdown with an 
alarm 

● 

● 

Battery  

Check the batteries for any leakage or loose connections. Batteries 
should be replaced every two years 

● 

 

Fire Dept 

Check emergency vehicle access device for proper operation 

● 

● 

Gate 

Inspect for damage 

● 

 

Reverse Sys-
tem 

Check that the gate reverses on contact with an object in both the 
opening and closing cycles 

● 

● 

Loop(s) 

Check vehicular reverse and shadow loops for proper operation 

● 

●  

Release 

Check manual release for proper operation 

● 

 

Complete 

Overall Check: Complete check of gate and gate operating system 

● 

 

Mounting Hard-
ware 

Check screws and nuts 

● 

 

14 - MAINTENANCE SCHEDULE - APOLLO GATE OPENER 

Summary of Contents for 1550ETL-1K

































Reviews: