Nibe F1255PC BE User Manual Download Page 70

Page: 70 / 88

ADVANCED

advanced 4.9

op. prioritisation

auto mode setting

degree minute setting

factory setting user

schedule blocking

off

advanced

has orange text and is

intended for the advanced user. This menu
has several sub-menus.

Menu
4.9

OP. PRIORITISATION

op. prioritisation4.9.1

min

hot water

heating

pool

op. prioritisation

Setting range: 0 to 180 min

Default value: 30 min

Choose here how long the heat pump should work with each requirement if
there are two or more requirements at the same time. If there is only one require-
ment the heat pump only works with that requirement.

The indicator marks where in the cycle the heat pump is.

If 0 minutes is selected it means that requirement is not prioritised, but will only
be activated when there is no other requirement.

Menu
4.9.1

NIBE F1255PC

Chapter 3 | F1255PC BE – at your service

Summary of Contents for F1255PC BE

























































































Search results

Summary of Contents for F1255PC BE

Reviews:

Related manuals for F1255PC BE

Brands by name

Popular brands

Nibe F1255PC BE, User Manual

Search results

Summary of Contents for F1255PC BE

Reviews:

Related manuals for F1255PC BE

Brands by name

Popular brands