background image

Sub-Head

NIBCO INC. WORLD HEADQUARTERS • 1516 MIDDLEBURY ST. • ELKHART, IN 46516-4740 • USA • PH: 1.800.234.0227  

TECH SERVICES PH: 1.888.446.4226 • FAX: 1.888.336.4226 • INTERNATIONAL OFFICE PH: +1.574.295.3327 • FAX: +1.574.295.3455

www.nibco.com

19

www.nibco.com

  A H E A D   O F   T H E   F L O W

®

NIBCO INC. LIMITED WARRANTY

Applicable to NIBCO INC. PEX Piping Systems

NIBCO INC. warrants that when NIBCO

® 

PEX tube is used with NIBCO

®

 PEX fittings, and NIBCO

® 

valves and installation 

accessories, they will, under normal conditions, use and service in potable water and radiant heat systems, be free from 

defects in materials and workmanship for a period of twenty-five (25) years from the date of purchase when installed by a 

licensed professional contractor. This 25-year warranty is voided if any non-NIBCO products are used in the PEX system. 

NIBCO INC. warrants NIBCO

 

PEX tube, when used under normal conditions, use and service in potable water and radiant 

heat systems with brass insert fittings meeting NSF/ANSI 61, ASTM F1807 and ASTM F877 to be free from defects in 

materials and workmanship for a period of ten (10) years form the date of purchase. NIBCO INC. warrants NIBCO

® 

PEX 

fittings, manifolds, transition fittings and valves under normal conditions, use and service in potable water and radiant 

heat systems, to be free from defects in materials and workmanship for a period of ten (10) years from the date of pur-

chase. NIBCO INC. warrants NIBCO

® 

associated hardware and tools for a period of 90 days from the date of purchase.

In the event any defect occurs which the owner believes is covered by this warranty, the owner should immediately contact 

NIBCO Technical Services, either in writing or by telephone at 1.888.446.4226 or 1.574.295.3000. The owner will be 

instructed to return said tube, fittings or accessories, at the owner’s expense, to NIBCO INC., or an authorized representative for 

inspection. In the event said inspection discloses to the satisfaction of NIBCO INC. that said tube, fitting or accessory is defective, 

a replacement shall be mailed free of charge to the owner.

IN ORDER FOR THIS LIMITED WARRANTY TO APPLY, THE ABOVE REFERENCED PRODUCTS MUST BE INSTALLED BY A 

LICENSED PROFESSIONAL PLUMBER IN ACCORDANCE WITH NIBCO INSTALLATION INSTRUCTIONS AND IN COMPLIANCE 

WITH ALL APPLICABLE CODE REQUIREMENTS. FAILURE TO DO SO WILL VOID ALL APPLICABLE WARRANTIES.

This warranty does not apply and you do not have a right of reimbursement if the failure or resulting damage is caused by:

1.  breaks, tearing, kinking, gouges, punctures or other external damages before, during, or after installation;

2.  exposure to temperatures and pressures beyond the product ratings as specified on the product or in the NIBCO    

 

installation manual;

3.  exposure to damaging chemicals, substances or corrosive water conditions;

4.  damage from abnormal operating conditions;

5.  damage due to accident, abuse, misuse, or unauthorized modification or repair;

6.  improper installation due to worn, damaged, unauthorized or improperly calibrated tools;

7.  components in the plumbing system other than those manufactured or sold by NIBCO;

8.  not designing, installing, inspecting or testing the system in accordance with NIBCO installation instructions at the   

 

time of the installation; or

9.  failure to follow applicable code requirements and good plumbing practices.

TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY SPECIFICALLY EXCLUDES INCIDENTAL AND CONSEQUENTIAL 

DAMAGES OF EVERY TYPE AND DESCRIPTION RESULTING FROM ANY CLAIMED DEFECT IN MATERIAL OR 

WORKMANSHIP, INCLUDING BUT NOT LIMITED TO, PERSONAL INJURIES AND PROPERTY DAMAGES.

Some states or countries do not allow the exclusion or limitation of incidental or consequential dam-

ages so these limitations may not apply to you.

TO THE EXTENT PERMITTED BY LAW, IMPLIED WARRANTIES OF MERCHANTABILITY AND 

FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION.

This warranty gives you specific legal rights, and you may also have other rights which vary 

from state to state and country to country.

To the best of our knowledge, the information contained in this publication is accurate. However, NIBCO does not assume any liability whatsoever for 

the accuracy or completeness of such information. Final determinations of the suitability of any information or product for the use to be contemplated 

is the sole responsibility of the user. The manner of that use, and whether there is any infringement of patents, is also the sole responsibility of the user.

Summary of Contents for PEX





















Reviews: