Nexus Cidron Combi Reader Installation Manual Download | Manualshive

Page: 19 / 32

background image

19

1:

Set the reader in programming mode, see page: 18

2:

Present the “Configuration Card” to the reader as shown. Keep

the card within reading distance until the reader beeps and blinks in
green. The reader is now programmed and ready for use according
to the configuration settings on the configuration card.

BEEP !

Configuring the reader

Reading distance

approximately 2 cm.

«
...
17
18
19
20
21
...
»

Summary of Contents for Cidron Combi Reader

































Reviews:

No comments

Related manuals for Cidron Combi Reader

Brand: H&S Pages: 46

Brand: National Instruments Pages: 13

Brand: Fisher Pages: 24

Brand: Magnavox Pages: 31

Brand: SAMUEL JACKSON Pages: 11

Brand: ICS Advent Pages: 34

Brand: Identix Pages: 6

Brand: Power Acoustik Pages: 4

Brand: Panasonic Pages: 98

Brand: D-Link Pages: 57

Brand: Asus Pages: 164

Brand: Asus Pages: 21

Hyper M.2 x16 Gen 4

Brand: Asus Pages: 10

Brand: Asus Pages: 4

Brand: Asus Pages: 5

Brand: Asus Pages: 12

AAEON Myriad PER-TAICX-A10-001

Brand: Asus Pages: 11

Brand: Asus Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands