background image

11

Tamper

GPO1
GPO2

GND

B/RX

A/TX
GND

DC+

CP
D1 Clock
D0 Data
GND
G-LED
R-LED
BZ CTRL
K-LED

P1

Blue

P2

Black

Tamper
GPO1
GPO2
GND
B/RX
A/TX
GND
DC+

CP
D1 Clock
D0 Data
GND
G-LED
R-LED
BZ CTRL
K-LED

Tamper output
General purpose I/O
General purpose I/O
Ground
RS485 -
RS485 +
Power supply
Power supply 9-30 VDC

Card Present
Wiegand Data1/Clock/Data, ABA2
Wiegand Data2/Clock/Data, ABA2
Ground
External Green LED control
External Red LED control
External Buzzer control
External Keypad LED control

Description

PIN

Wiegand

x

-
-

x

-
-

x
x

-

x
x
x
x
x
x
x

P1 - Blue

P2 - Black

RS485/

OSDP

Clock/

Data

-
-
-

x
x
x
x
x

-
-
-

x

-
-
-
-

-
-
-

x

-
-

x
x

x
x
x
x
x
x
x
x

Notes:

1. Maximum wiegand cable length is 150 meters and requires a high 
quality shielded cable with minimum AWG18 dimension (=0.8231mm2) 
in an environment free from electrical noise.
2. Wiegand requires dedicated wires for external control of green LED, 
red LED, buzzer and keypad backlight LED.
3. When utilizing the GPI/O’s, each respective GPO1 or GPO2 must 
be connected to each respective pin and also to GND. The general 
purpose input/output will only be activated if so applied in the reader 
configuration. 
4. RS485/OSDP requires twisted pair cable.

Summary of Contents for Cidron Combi Reader

































Reviews: