manualshive.com logo in svg

Nexo GEO M12 Series, System Manual

Share
Download
Nexo GEO M12 Series System Manual Download Page 36

Page 36/90 

GEO

 

M12

 

HARDWARE

 

SETUP

 

PROCEDURE 

 

 

 

 

- 

Adjust feet height so that bumper is horizontal 

 

 

 

- 

Pull latch to release the VNT-BUMPM12 center link bar, and rotate it upwards 

- 

Pull the bumper front latches, rotate the upper link so that connection points are single leg (GEO M12 
Left) or double leg (GEO M12 Right) and release the latches to lock in required position 

 

 

 

 

GEO M12 Left 

- 

Release first GEO M12 link bar, and set AutoRig in automatic lock position 

- 

Position first GEO M12 on top of the bumper, front points will lock automatically 

- 

Connect the bumper link bar (selection from -12° to +12° in 3° steps) to GEO M12 rear rigging plate 
(hole marked “bumper”) Lock with the quick release pin BL0820. 

 

GEO M12 Right 

- 

Release first GEO M12 link bar. 

- 

Position first GEO M12 on top of the bumper and lock it to the bumper with the 2 BL820 quick release 
pins. 

- 

Connect the bumper link bar (selection from -12° to +12° in 3° steps) to GEO M12 rear rigging plate 
(hole marked “bumper”) Lock with the quick release pin BL0825. 

 

Subsequent GEO M12s 

- 

Position second GEO M12 cabinet with AutoRig

TM

 in automatic lock position, and lock front points to 

first GEO M12 

- 

Unlock GEO M12 link bar 

- 

Pull the latch to engage the guide in GEO M12 rear slot. 

- 

Adjust the angle by inserting quick release pin BL820 in proper hole. 

Summary of Contents for GEO M12 Series



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands