background image

         

TROUBLE SHOOTING 

 

 

 

Problem    Possible Causes                    Correction  

 

 

Purge gas line and repeat ignition operation   

 

Check gas pressure   

 

Check gas passage way   

 

 

 

Reset the Heater keep in vertical position   

 

Replace thermocouple   

 

Clean thermocouple contact   

 

Wait a minute repeat ignition operation   

 

Replace gas valve   

 

Tighten connection or replace thermocouple   

 

 

Contact a qualified service person 

 

 

 

 

Check gas supply pressure   

 

Clean burner inside and outside   

 

Turn control knob to ‘HIGH’ position 

 

 

Air in gas line   

 

Low gas pressure   

 

Blockage in gas line   

 

   

 

Tilt switch in trip angle/OFF position   

 

Bad thermocouple   

 

Corrosion of thermocouple contact   

 

Safety interlock is triggered   

 

Bad gas valve   

 

Thermocouple connection loose at gas 

control or damaged   

 

Pilot flame not touching the   

thermocouple 

   

 

 

Low gas pressure   

 

Blockage in burner   

 

Control knob not in ‘HIGH’ position 

 

Pilot won’t   

light

 

 

 

 

Pilot won’t   

stay lit

 

 

 

 

 

 

 

 

 

 

 

 

Main burner   

won’t light 

 

 

 

 

 

 

 

Page 12 

 

Summary of Contents for T-005
















Reviews: