background image

 

November 2017 

Page 2 

 

 

Content 

 

1.

 

General Information

 ......................................................................................................................... 3

 

1.1

 

Document Purpose

 ............................................................................................ 3 

1.2

 

Definitions, Acronyms and Abbreviations

 ...................................................... 3 

2

 

Product Overview

 ............................................................................................................................. 6

 

2.1

 

About the NIO200 Gateway

 ............................................................................. 6 

2.2

 

Logical Interfaces

 ............................................................................................... 6 

2.3

 

Package Contents

 .............................................................................................. 7 

3

 

Getting Started

 .................................................................................................................................. 8

 

3.1

 

Installation background

 ..................................................................................... 8 

3.2

 

Hardware installation Guide

 ............................................................................. 8 

3.2.1

 

Water proof connector installation

 ................................................................... 9 

3.2.2

 

Power installation

 ............................................................................................. 10 

3.2.3

 

Antenna installation

 ......................................................................................... 11 

3.2.4

 

Earth grounding

 ................................................................................................ 12 

3.2.5

 

Mounting of NIO200

 ........................................................................................ 12 

3.3

 

Wi-Fi Mesh Network Configuration

 ............................................................... 15 

3.3.1

 

Access to NIO200 Admin website

 ................................................................. 15 

3.3.2

 

Configure the IP Address

 ................................................................................ 15 

3.3.3

 

Change IPv4 address

 ...................................................................................... 17 

3.3.4

 

Enable NTP (Network Time Protocol)

 .......................................................... 19 

3.3.5

 

Select Time Zone

 ............................................................................................. 19 

3.3.6

 

Select/Input Time Server

 ................................................................................ 20 

3.3.7

 

Configure Wi-Fi Mesh Interface

 ..................................................................... 21 

3.3.8

 

Configure Physical Settings for Radio

 .......................................................... 23 

3.3.9

 

Network Settings of Wi-Fi Interface

 .............................................................. 24 

 

 

 

Summary of Contents for NIO200

























Reviews: