Nexans EUROMOLD K800PB/G Installation Instructions Manual Download Page 12

Page: 12 / 14

coupling

connector

30 Nm

Install the M16 threaded stud into the contact rod.

Using a 13 mm wrench or a hex key of 8 mm, tighten the stud exerting

Nm (3 kgm or 22,1 foot-pounds).

In order to achieve the correct applied torque ensure that there is no lubricant on the threaded

parts.

Clean and lubricate* both female tee connector interface and male interface of the coupling connector.

Push the coupling connector on to the contact rod of the tee connector. Take care not to damage the contact rod

during installation of the coupling connector.

Install the flange nut on to the threaded stud.

Use torque wrench with extension and a 22 mm socket and tighten exerting

Nm (5 kgm or 36,9 foot-pounds)

of torque.

In order to achieve the correct applied torque ensure that there is no lubricant on the threaded

parts.

22 mm

socket

1/2" - 12,7 mm

torque wrench

L ≥ 130 mm

extension

coupling

connector

22mm

* USE ONLY THE SILICONE LUBRICANT SUPPLIED

50 Nm

contact

rod

M16

stud

equipment

bushing

equipment

bushing

Type 2: flange nut

M16

flange nut

IS97180-ENG - K800PB/G

-CW45-

CA0 - Revision 2

Page 12 of 14

For

information

only

Summary of Contents for EUROMOLD K800PB/G















Search results

Summary of Contents for EUROMOLD K800PB/G

Reviews:

Related manuals for EUROMOLD K800PB/G

Brands by name

Popular brands

Nexans EUROMOLD K800PB/G, Installation Instructions Manual

Search results

Summary of Contents for EUROMOLD K800PB/G

Reviews:

Related manuals for EUROMOLD K800PB/G

Brands by name

Popular brands