Detector is
triggered
Light
turns on
15 seconds
Triggered
180
seconds
Triggere
is inoperable.)
seconds).
3. Node ID is excluded. The device reverts to
factory default state and will be in
auto-inclusion mode for 4 minutes.
2-second on, 2-second off
For 2 minutes
Failed or successful results in including/excluding the ID can be viewed on the Z-Wave Controller.
3.
Lux Level
Detected a
movement
Detected a
movement
(no response)
Detected a
movement
Note
: If you are connecting this unit to a Z-Wave Controller that utilizes the S2 security protocol, you may
be asked to enter a 5 digit Device Specific Key (DSK) that is unique to each unit by your controller. This
can be found in one of two places:
- on the QR code label on the back of the unit
- on the insert card inside the packaging
Table below lists typical problems encountered:
The user can set a detecting percentage of lux level which determines when the light sensor will
be activated. If percentage of lux level of ambient illumination falls below this percentage, and a
person moves across or within the protected area, the detector will emit Z-Wave ON Command
(i.e. Basic Set Command (Value = Basic Set Level)) to controller and activate connected modules
and lighting. Percentage can be set between 1% to 100%.
Function
Parameter Number
Size
Range
Default
Lux Level
5
1
1~100 %
20
4.
On-Off Duration
The function of on-off duration setting will be useful if the detector is connected with a module or
lighting. The duration determines how long the module/lighting should stay ON. For instance,
Lamp Module turns off 100 secs after it has been turned on. This parameter can be configured
with the value of 5 through 3600, where 5 means 5 second delay and 3600 means 3600 seconds
of delay.
Function
Parameter Number
Size
Range
Default
On-Off Duration
6
2
5~3600(sec)
15
Troubleshooting
Detected a
movement
Light
turns off
Specifications
The table below lists the several steps involved when adding or removing the detector from the Z-Wave
network.
Specifications are subject to change without notice
*measured at 10 triggers per day
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
Symptom
Possible Cause
Recommendation
Cannot carry out inclusion and
association
1.
Run out of battery power
2.
Check if reverse battery
polarity
3.
Check if the detector is out
of order
1.
Replace a new battery
2.
Refit the battery with
correct polarity
3.
Ensure the detector is
working properly
Cannot control the connected
modules
1.
Run out of battery power
2. Check if the detector is out
of order
1.
Replace a new battery
2.
Ensure the detector is
working properly
The detector not working
1.
Run out of battery
power
2.
Check if the mounting
location is proper
3.
Check if the detector is
mounted above a radiator
or heater
4.
Check if the detector is out
of order
1.
Replace a new battery
2.
Reposition its mounting
location
3.
Remove the source of
interference or
reposition its mounting
location
4.
Ensure the detector is
working properly
Battery
CR123 3.0V 1700mAh Lithium Battery
Battery Life
1 year*
Range
Up to 100 meters line of sight
Warm Up Time
About 2 minutes
PIR Detection Coverage
Up to 10m x 110° (at 1.8m mounting height & 25°C)
Operating Frequency
EU: 868.42HMz
US: 908.42 MHz
JP: 922.5MHz
FCC ID
FU5SP817
IC
23210-SP817
Action/Status
Description
LED indication
No node ID
The Z-Wave Controller does not allocate a node
ID to the unit.
2-second on, 2-second off
For 2 minutes
Auto Inclusion
The power is applied for the first time and no node
ID has been stored in the module, or after
executing reset.
Manual Inclusion
1. Put the Z-Wave Controller into
inclusion mode.
2. Press the tamper switch 3 times within 1.5
seconds to put the unit into inclusion mode.
Exclusion
1. Put the Z-Wave Controller into exclusion mode.
2. Press the tamper switch 3 times within 1.5
seconds to put the unit into exclusion mode.
Factory Reset
(This procedure
should only be used
when the controller
1. Press the tamper switch 3 times within 1.5
seconds to put the unit into exclusion mode.
2. Within 1 second of step 1, press the tamper
switch again and hold until LED is off (about 5
