Newgrind RHINO RLP800 User Manual Download Page 9

                                                                                                                                                 

RLP800 Users Manual 

 

MEDIUM EXPOSURE:

 Severe throbbing headache, dizziness, drowsiness, confusion, fast 

heart rate. 

EXTREME EXPOSURE:

 Unconsciousness, convulsions, cardiorespiratory failure, brain 

damage, death. 
 

Many cases of 

CARBON MONOXIDE 

POISONING

 indicate that while victims are aware 

that they are not well, they become so disoriented 

that they are unable to save themselves by either 

exiting the building or calling for assistance. Older 

adults, young children, pregnant women (and 

their unborn children), and persons with medical 

conditions are typically the first affected. 

 

Prior to starting the grinder 

 

1.

 

Inspect the grinder to make sure all bolts are tight, and that tools are properly mounted 

2.

 

Check that propane tanks are properly mounted and that the gas connectors are secure 

Starting the grinder 
 

DO NOT LIFT THE EQUIPMENT OFF THE GROUND WHILE STARTING!

  

Doing so can cause the tools to release from the equipment and cause damage to 
the surface being finished and harm to the user! 

1.

 

Open the valve on the propane tank 

2.

 

Move the throttle lever to half throttle position 

3.

 

Use full choke when the engine is cold, but in hot weather or when the engine is already 
warm use half choke or leave the choke fully open 

4.

 

With the machine in an upright position, set the articulating handle to the desired 
position. 

5.

 

Apply downward pressure on the handle to alleviate some pressure on the tools and  

6.

 

Put the switch key into the engine switch 

7.

 

Turn the key to the start position.  Usually the engine will start within 3 seconds 
 

Summary of Contents for RHINO RLP800























Reviews: