background image

1002-6

DIESEL FUEL SYSTEM

Use No. 2 diesel fuel in the engine of this machine.

The use of other fuels can cause the loss of engine

power and high fuel consumption. 
In very cold temperatures, a mixture of No. 1 and No.

2 diesel fuels is temporarily permitted. See the

following Note.

NOTE:

See your fuel dealer for winter fuel

requirements in your area. If the temperature of the
fuel lowers below the cloud point (wax appearance
point), wax crystals in the fuel will restrict the fuel
filter and cause the engine to lose power or not start. 

The diesel fuel used in this machine must meet the

specifications as shown below in, “Specifications for

Acceptable No. 2 Diesel Fuel”, or “Specification

D975-81” of the American Society for Testing and

Materials.

Fuel Storage

If you keep fuel in storage for a period of time, you

can get foreign material or water in the fuel storage

tank. Many engine problems are caused by water in

the fuel. 
Keep the fuel storage tank outside and keep the fuel

as cool as possible. Remove water from the storage

container at regular periods of time. 
Fill the fuel tank at the end of the daily operating

period to prevent condensation in the fuel tank.

Specifications for Acceptable No. 2 Diesel Fuel 

API gravity, minimum ............................................................................................................................................. 34

Flash point, minimum  ............................................................................................................................60°C (140°F)

Cloud point (wax appearance point), maximum  ...........................................................-20°C (-5°F) See Note above

Pour point, maximum ..................................................................................................-26°C (-15°F) See Note above

Distillation temperature, 90% point ................................................................................282 to 338°C (540 to 640°F)

Viscosity, at 38°C (100°F) 

Centistokes ......................................................................................................................................... 2.0 to 4.3

Cetane number, minimum  ..........................................................................  43 (45 to 55 for winter or high altitudes)

Water and sediment, by volume, maximum  .................................................................................................... 0.05%

Summary of Contents for W110C










































Reviews: